Bedienungsanleitung Kress sblr 2362 (Seite 6 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

386730

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

1ON/OFF switch with full wave electronic control and

adjusting wheel for speed selection

2Holding button for continuous operation

3Reversing switch

4Switching from normal drilling to percussion drilling

5Mains cable with patent quick-release lock

6Locking device for mains cable module

7Quick-change chuck

8Auxiliary handle (optional accessory)

Technical dataSBLR 2362/s

Input 620 W

Output 340 W

Rotation right/leftx

No. of speed ranges1

No-load speed r.p.m. 0–3400

Load speed r.p.m. 1710

Percussion rate p.m. n x 16

Max. drill dia. into steel mm 13

Max. drill dia. into wood mm 30

Max. percussion drill dia into

concrete mm 16

Max. screwing into wood mm 6

Max. screwing into

Sheet metal mm 6.3

Collar diameter, mm 43

Chuck dia., mm 13

Spindle thread1/2” x 20 UNF

Weight kg 1.7

Use

This drill is universally suitable for use as a hammer drill

with stone, as a screwdriver with wood, metal and plastic,

and for cutting threads.

The drill is not suitable for heavy stirring or drilling

holes with large diameters.

Safety instructions and prevention of accidents

Before operating the machine, please read through the

operating instructions completely, follow the

Safety

instructions

in this manual as well as the general Safety

instructions for powertools

in the accompanying

booklet.

Caution!

Ⴇ Beware of jamming. The machine may jam, for ex-

ample, when the machine is at an angle or when the

drill bit comes into contact with reinforcing steel!

Ⴇ B efore fitting tools in the chuck or drill spindle dis-

connect the machine from the power supply, or re-

move the mains cable with patent quick-release lock

(5) from the grip using the locking device button (6)!

Ⴇ Do not work with materials containing asbestos!

Ⴇ Outside power sockets must be protected with

residual-current-operated circuit-breakers (r.c.c.b.).

Ⴇ Do not drill holes into the housing to label the

machine. The protective insulation will be bridged.

Please use self-adhesive labels.

Ⴇ Always lead cables away towards the back of the

machine.

Double insulation

Our equipment is designed in accordance with European

regulations (EN standards) for the utmost safety of the

user. Machines with double insulation always carry the

international symbol. The machines should not be

earthed. A two-core cable is sufficient.

The machines are interference-suppressed in accordance

with EN 55014.

Initial operation

Before the first operation check that the mains voltage cor-

responds to that given on the machine nameplate.

Trigger switch with button for continuous operation

The machine is set in operation by pressing in the handle

switch (1). The small holding button (2) on the side of the

switch is pressed in for continuous operation. To release

the continuous operation merely depress the switch, which

makes the holding button spring back automatically.

Electronic speed control

This machine has an integrated full wave electronic control

circuit switch.

The required speed may be selected with the adjusting

wheel (e.g. for serial screw drilling or for cutting threads).

The switch is lockable in every position.

Position A = lowest speed

Position G = highest speed

Ensure that the drill is not allowed to jam for longer

than 2–3 seconds. Longer jamming can lead to motor

damage.

Important!

Continuous operation under strong load and low speed

can overheat the motor. Allow the motor to cool down

in no-load when set at a high speed!

Changing direction of rotation

(main rotation – clockwise)

The direction of rotation of the spindle is changed using

the reversing switch (3).

R=Clockwise (Right)

L=Anticlockwise (Left)

Important!

Press the reversing switch until it reaches the respec-

tive end position at the housing, i. e. until it can be felt

to engage!

The reversing switch is easiest to operate by using the

thumb and index or middle finger from both sides.

Attention!

Change direction of rotation only when the motor has

ceased turning!

When using the drill as a screwdriver, the percussion

mechanism must be switched off. Switch-over by

means of the sliding switch (4).

Percussion drilling device

The machine has an integrated percussion mechanism and

can be switched from normal drilling to percussion drilling.

The sliding switch (4) allows switching from normal drilling

to percussion drilling or vice-versa while the machine is in

operation.

Normal drilling position

Move slide switch (4) to the left in direction of normal

drilling.

Percussion drilling position

Move slide switch (4) to the right in direction of percussion

drilling.

Screwdriving

You can fit screwdriver bits directly into the drill chuck. For

best results use Phillips screws. Safe working is made

possible by the self-centering feature. Please be sure that

you also use the correct screwdriver bits.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress sblr 2362 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info