Bedienungsanleitung Kress sblr 2362 (Seite 7 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

386730

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Cutting threads

The integrated electronic and the reversal of the direction

of rotation makes the percussion drill also suitable for cut-

ting threads. The use of machine taps is recommended.

The tap is clamped into the chuck. The electronic controls

are sensitive and should be handled with utmost care to

prevent any breaking of tap – particularly when cutting

threads into blind holes.

The torque required can be selected via the adjusting

wheel in switch (1).

Important! When cutting threads, use low speeds only.

Drill chuck

The drill chuck is tightened with a torque of 30 Nm. Only in

this way is it guaranteed that the chuck does not loosen

itself from the spindle during anticlockwise rotation.

If the chuck is removed from the spindle for replacement

purposes, the new chuck must be tightened with a torque

of at least 30 Nm before restarting the machine.

Before applying a new chuck, the surfaces of both the

chuck and the spindle must be cleaned.

Caution!

Before disassembling and reassembling the drill chuck,

either disconnect the machine from the power supply,

or remove the mains cable (5) from the grip using the

locking device buttons (6).

Caution!

When turning anticlockwise, it is possible that the

chuck loosens itself from the spindle. For this reason

make sure that the chuck sits properly on the spindle.

Operating the quick-change chuck

This chuck has been developed especially for use with

percussion drills.

The fully-automatic spindle locking device enables a quick

and problem-free tool change in the chuck.

The drill spindle will be automatically fixed when the chuck

is actuated.

The chuck has a release safety lock which prevents any

unintentional release of the drilling tool even at high impact

frequencies.

After attaching the jaw chuck to the tool, a slightly higher

torque must be used to engage the clamping force safety

lock. The torsion angle of the collar must be approximately

50°during the locking procedure. After this has been

completed, the tool can be tensioned as usual. Turn the

collar firmly in the “ZU” direction until a click is heard. The

drill is only properly tensioned when the collar has been tur-

ned as far as possible and no more clicking is heard.

Always make sure that the chosen speed is correct for

the purpose for which you are using the machine.

High speeds are necessary for polishing and grinding.

When drilling match speed with type of material and drill.

High speed drilling in steel and stone will cause premature

tool wear.

Use tool steel twist drills for soft materials such as wood

and plastics; carbide-tipped stone drills for stone and con-

crete; high speed twist drills for steel and iron.

Also make sure that, using a gear-rim-chuck, the drill

chuck key is never fastened to the drill with chains,

strings or by similar means. Be sure that the workpiece

cannot be taken along by the drill.

Maintenance

The machine’s motor has life-time lubrication and requires

no special maintenance. However, should you operate the

machine on a continuous basis over long periods of time

we recommend that you send us the machine for thorough

cleaning and an inspection. This will spare you unneces-

sary repair expenses and increase the machine’s service

life. If you always clean the ventilator of dust after each

operation, the motor will enjoy an ever longer service life.

Uniform ventilation is essential for a long service life.

Replacing carbon brushes

Our service personnel will do this and all other servicing

work fast and professionally.

Mains cable

Damaged mains cables must not be used. They are to be

replaced immediately.

Thanks to the innovative mains cable with patent quick-

release lock (5) it is possible for you to replace the cable

with the greatest of ease. Press the two lock pushbuttons

(6) and pull the mains cable (5) out of the casing. Feed the

new mains cable into the hand grip until it snaps in place.

Various cable lengths are available upon request.

Only use the mains cable module for KRESS power

tools! Do not try to operate other power tools with it!

Auxiliary handle (optional accessory)

Guarantees safe, wander-free guidance of the drill, and at

the same time precise adjustment of the drilling depth with

the depth stop.

Tighten the tensioning screw on the auxiliary handle

well. This is the only way to prevent the auxiliary handle

from twisting on the collar or from coming off the unit.

We reserve the right to make alterations resulting from

technical development without prior notice.

Noise/vibration information

Measured values correspond with EN 50144.

Sound pressure level = 74

dB (A)

Sound power level = 87

dB (A)

Work place emission value=77

dB (A)

Operators require noise protection equipment.

The weighted acceleration is typically 13.2 m/s

Environmental protection

Kress takes back old machines for resource saving recyc-

ling. Kress machines can very easily be broken down into

their recyclable basic materials. Hand in your old Kress-

machine at a dealer or send it directly to Kress.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress sblr 2362 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info