Bedienungsanleitung KRK Systems Rokit Powered G2 Series (Seite 14 von 20) (Englisch)

705171

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

If there is no power, check to see if...

Troubleshooting

If you can’t hear any sound...

If the monitor suddenly stops working...

If you’re having trouble, check out these tips...

• The power cord is plugged into both the IEC socket on the rear panel of the monitor

and into the AC mains. The KRK logo on the front face plate will illuminate when the

monitor is powered on.

• The AC mains voltage is matched to the operating voltage requirements

(see Changing Voltage in the Connecting Your System section on page 8). If the

AC mains voltage is higher than the selected voltage on the RoKit, it is possible that

the fuse needs to be replaced (see Changing Fuses in the Connecting Your System

section on page 8).

• The KRK logo is illuminated on the front panel of the RoKit. If not, turn the power

switch off and check the AC mains fuse(s). NEVER USE A LARGER AMPERAGE

FUSE THAN IS SPECIFIED! Turn the power switch back on. The power light should

illuminate.

• Note: If a fuse change is required, please check that the AC mains voltage is set correctly.

If the fuse(s) blow again when the monitor is turned on, please contact the dealer you

purchased it from, or KRK Customer Service (1-800-444-2766 or Service@Gibson.com).

• Repeat the steps in the Troubleshooting section above before continuing to the next

steps.

• Check to see if all other audio devices using the same AC outlet are still operating.

• Make sure that:

• The audio source cable is plugged into both the source output and the

monitor input.

• The System Gain pot is turned up fully clockwise (+6dB).

• The signal source (e.g. mixing console, work station, CD player, etc.) is

turned up to a level that can properly send a signal to the monitors.

• Check to see if one of the monitors is working. Exchange the audio input cable from

the non-working monitor to the working unit. This will determine whether it's really the

monitor, a faulty cable, or some other glitch in the audio chain.

• If the monitor is still not responding, it should be returned to the dealer that you

purchased it from, or to KRK, for servicing.

• Turn the monitor send down or off.

• Repeat the steps in the Troubleshooting sections above before continuing to the

next steps.

• Carefully check to see if the amplifier’s back plate is hot! If the monitor has been

running at its highest power output for an extended period of time, it could be that the

unit has become overheated and the protection circuitry has shut the system

down momentarily. Your RoKit G2 monitor provides maximum circuitry protection

against AC power surges, amplifier overdrive, and overheating of the amplifiers. Turn the

monitor off then wait 30 minutes to allow the back plate to cool down. Turn the power

switch back on.

• Increase the volume to check for normal operation.

• If the monitor is still not responding, please contact the dealer you purchased it from or

KRK Customer Service (1-800-444-2766 or Service@Gibson.com).

rokit_manual REV E_rokit_manual 2/19/13 10:24 AM Page 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KRK Systems Rokit Powered G2 Series Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info