Bedienungsanleitung Krups EA 8050 (Seite 6 von 16) (Englisch)

111147

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Place a receptacle under the steam nozzle. Run 300 ml of water by pressing the rinse button once for more than 3

seconds. You can repeat this operation if you wish.

Settings

Connect the appliance to the mains power supply but do not turn it on.

Lift the cup grid by pressing on the back to make it tilt.

Press the and

- Fig. 5

The digital display for parameter setting is under the servicing ap

- Fig. 6

Look down vertically to the bottom of the window

- Fig. 7

Setting water hardness

The “water tank” light will come on.

Press the key

- Fig. 8

as many times as are needed to select the hardness level for the water used : 0 = very soft, 1 =

soft, 2 = moderately hard, 3 = hard, 4 = very hard.

Setting the coffee temperature

Press the steam key to switch to coffee temperature setting : The ‘

CALC

’ light will come on.

Press the key

- Fig. 8

as many times as are needed to select the desired coffee temperature : 1, 2 or 3.

Setting the automatic electrical power supply cut-off (auto-off)

It is possible to turn your machine off automatically after a number of pre-programmed hours.

Press the steam key

to switch to automatic cut-off setting :The ‘

CLEAN

’ light will come on.

Press the key

- Fig. 8

as many times as are needed to select the desired duration: 1 = 1 H, 2 = 2 H, 3 = 3 H, 4 = 4 H.

Preparing the appliance

Pull out and ll the water tank

- Fig. 9

Put it back in place by pressing rmly and close the lid again

- Fig. 10

Open the coffee bean container lid. Add the coffee beans

- Fig. 11

Close the coffee bean container lid again.

NEVER PUT GROUND COFFEE IN THE COFFEE CONTAINER.

It is recommended that you do not use oily, caramelised or avoured coffee beans for this machine. These kinds of beans

may damage the machine.

Check that the coffee beans do not contain any foreign particles such as grit, as any damage caused by the presence of

foreign particles will negate the warranty.

Appliances are pre-set in the factory to 1 hour.

At each of these stages, you can memorise your settings by pressing the button when you have reached the setting

you want (the 4 lights ash 2 times) or carry on with the procedure. These settings will remain memorised even if the

electrical power is cut off. You can modify these settings at any time by repeating these operations.

Appliances are pre-set in the factory to 2, average temperature.

Appliances are pre-set in the factory for hardness level 4.

The Claris cartridge needs to be replaced after about every 50 litres of water or every two months at least.

Do not ﬁll the water tank with hot water, milk or any other liquid.

If you turn on the appliance when the water

tank is not in place or not correctly lled (under the “min.” level,), the “ll water tank” light will come on and making

an espresso or a cup of coffee will be made impossible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups EA 8050 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Krups EA 8050

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info