Bedienungsanleitung Krups EA 8050 (Seite 10 von 16) (Englisch)

111147

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Press the button after having carried out all of these operations.

1 - Descaling cycle ± 8 mn

The ‘

CALC

’ light stops blinking. The descaling cycle starts and is carried out automatically. The pump

occasionally sucks up water which comes out of the coffee nozzles and then the steam nozzle. This operation

lasts approximately 8 minutes.

When the cycle has completed, the ‘

’ and ‘

CALC

’ lights blink.

2 - First rinsing ± 6 mn

A rst rinsing is needed to eliminate the remaining scale remover. This cycle is run automatically. It lasts about

6 minutes.

Empty your receptacle full of waste water.

Empty the drip tray and then put it back again together with the receptacle as previously.

Empty, clean and rinse the water tank and then ll it again up to the “Max. level.

Replace your water tank. The ‘

CALC

’ light will ash and the ‘ ’ light will go off.

Press the

key. The ‘

CALC

’ light will become steady. The automatic cycle will last 6 minutes.

3 - Second rinsing

At the end of the rst rinsing, the ‘

CALC

’ light will ash. A second automatic cycle will last 6 minutes.

Remove your waste water recipient and the drip tray then t them again.

Again press the key. The ‘

CALC

’ light will become steady.

A second automatic cycle will last 6 minutes.

Once the second rinsing is nished, the ‘

CALC

’ light will go off.

Empty the drip tray and then t it again.

Empty and then ll your water tank.

Your appliance is now ready for use again.

Be sure to complete the entire scale removal cycle to avoid any risk of intoxication. The scale removal cycle

is a continuous cycle. Do not put your hands under the coffee outlets during the cycle.

Long rinsing program

When it is necessary to make a long rinsing program, the appliance warns you of this by ashing the ‘

CLEAN

’ and ‘

CALC

’

lights.

Remove, ll and replace the water tank.

Under the coffee outlets and steam nozzle place a recipient that can contain at least 0.15 L.

Launch the long rinse program by pressing on the button.

When the long rinsing program is complete, the ‘

CLEAN

’ and ‘

CALC

’ lights turn off.

TROUBLESHOOTING, CORRECTIVE ACTIONS

If one of the problems described in the table persists, contact KRUPS customer service.

If there is not enough water in the water tank, you will be warned by the ‘ ’ light.

Add the appropriate amount of water to the tank and scale removal will continue automatically.

If a power failure occurs during the cycle, you will have to start it up again from the start.

PROBLEM MALFUNCTION CORRECTIVE ACTION

Your machine detects a fault.

Switch off and disconnect the machine, remove the lter cartridge, wait for a

minute and restart the machine.

The appliance does not turn on

when the

button is pressed.

Check your fuses and plug sockets.

Check that the two power plugs are correctly pushed in the socket.

The coffee grinder makes a strange

noise.

There is a foreign body in the grinder. Disconnect the machine before investigating.

See if you can extract the foreign body using your vacuum cleaner.

The steam nozzle makes a noise. Check that the steam nozzle is correctly attached to its corresponding end piece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups EA 8050 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Krups EA 8050

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info