Bedienungsanleitung Krups f 880 (Seite 18 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

361241

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

. FROTHING MILK FOR A CAPPUCCINO

When preparing an espresso, this machine

can be used to produce frothy milk to prepare

a cappuccino.

For best results, use the cappuccino accessory.

Please note: The cappuccino accessory

must only be used for producing frothy

milk.

•Fit the accessory to the end of the steam

nozzle (17).

•Pour about 200 ml of skimmed milk into a

small high-sided container (maximum

capacity 0.5 L) which will fit beneath the

steam nozzle.

The milk must be nice and fresh, and the

container must also be chilled, so do not rinse

it in hot water beforehand.

• Check that the boiler is full of water.

The pump switch must be in position

(18).

When the yellow temperature indicator light

goes out:

• Place a container under the steam nozzle

and turn the steam tap to max position.

•Let the water flow until steam appears, then

turn the tap back to position O.

You can now start to prepare frothy milk.

• Place a container under the steam nozzle in

such a way that it is completely immersed in

the milk.

• Turn the tap slowly to max position and

hold the container steady during the

operation (19).

The nozzle must not touch the bottom of the

container so as not to prevent the steam

escaping.

• Once you have obtained the froth, reset the

tap to position O and remove the container.

• Then set the tap to steam position again for

a few moments (with an empty container

under the nozzle) to eliminate the residue of

milk in the nozzle.

• Once this operation is finished, clean the

cappuccino accessory and the steam nozzle

with a damp cloth.

. HEATING OTHER LIQUIDS

• Take out the steam nozzle.

• Remove the cappuccino accessory.

• Make sure the boiler is full of water.

• Set the pump switch to position

• Switch on the appliance.

A little water and steam will escape from the

percolation head while the appliance is

heating up.

• When the yellow temperature indicator light

goes out, place a container under the steam

nozzle and turn the steam tap to max

position.

• Let the water flow until steam appears, then

turn the tap back to position O.

• Place the container under the steam nozzle

in such a way that the jet is immersed in the

liquid.

• Turn the tap slowly to max position.

• Once the liquid is hot enough, reset the tap

to position O and remove the container

from the nozzle.

Note :

If you wish to prepare an espresso

immediately after using steam, it is vital that

you allow the appliance to cool down to the

«coffee making» temperature :

• Place a container under the filter holder and

set the pump switch to the « » position.

• Let the water run through until the yellow

temperature indicator light goes out.

• Reset the pump switch to position

, after

which you may prepare an espresso in the

usual way.

Cleaning

• Before doing any cleaning, unplug the

appliance and allow it to cool down.

• Wipe the body of the appliance with a

damp cloth.

The water tank must be emptied after use.

• Remove the cup rest grid and clean it (20).

• Empty the drip tray and clean it.

ART. 880.PM6.5 19/01/04, 16:0118

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups f 880 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info