Bedienungsanleitung Ksenia Lares 4.0 (Seite 46 von 58) (Englisch)

693399

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

rev. 0/2018

lares 4.0 PROGRAMMING MANUAL

Type: Remote control

The subtypes available are:

• Switch-off button: runs the scenario by pressing the Switch-off button on the remote control (short pressing).

• Partial button pressing: runs the scenario by pressing the Partial button on the remote control (short pressing).

• Pressing the Total button: runs the scenario by pressing the Total button on the remote control (short pressing).

• Long pressing of the Switch-off button: runs the scenario by pressing the switch-off button on the remote control

(long pressing).

• Long pressing of the Partial button: runs the scenario by pressing the Partial button on the remote control (long

pressing).

• Long pressing of the Total button: runs the scenario by pressing the Total button on the remote control (long pressing).

• Long pressing of the "i" button: runs the scenario by pressing the (i) button on the remote control (long pressing).

Type: Key ID

The subtypes available are:

• Code recognized: runs the scenario when a code is recognized. Valid option for codes entered on the keypad or APP.

• Key recognized: runs the scenario approaching a Key enabled to the reader (keypad or ﬂight/ﬂight-IN).

Type: Motherboard

The subtypes available are:

• Tamper: runs the scenario when a tamper condition occurs in the metal box of the control panel (opening and/or

detachment from the wall) detected through the switches connected to the T connector of the "lares" card.

• Tamper reset: runs the scenario when the tamper condition of the control panel box is reset.

• Start of maintenance: runs the scenario when a new conﬁguration is applied.

• End of maintenance: runs the scenario when parameter programming, via portal or installer app, is completed

• Periodic test: runs the scenario based on a scheduled periodic event (test event).

• Wrong code: runs the scenario after three incorrect codes have been entered on the keypad. After four incorrect

codes, the keypad is blocked for (90s.).

• Recognized installer PIN: runs the scenario when the installer PIN code is recognized.

• Control panel power off: runs the scenario when a system shutdown event occurs (230V power is off and the battery

is discharged). In this case we should preserve the battery from total discharge.

• Control panel reset: runs the scenario when the control panel has restarted because the power has been lost and

subsequently restored or due to a system fault or due to a ﬁrmware update.

• Ethernet network failure: runs the scenario when the Ethernet cable is disconnected (or when the router/switch is

turned off).

• Ethernet network restore: runs the scenario when the Ethernet cable is reconnected (or when the router/switch is

turned on).

• PSTN network failure: runs the scenario when the telephone line is removed from the PSTN module (cable cut or line

failure).

• PSTN network restore: runs the scenario when the telephone line on the PSTN module is restored.

• No GSM network: runs the scenario when the GSM network is missing (no signal, GSM repeater malfunctioned or

switched off for maintenance, SIM disabled and no longer registered on the network of the mobile operator).

• GSM network restore: runs the scenario when the GSM network is restored.

• Failed superv. IP receiver: runs the scenario when the IP receiver fails to send supervision.

• IP receiver reset: runs the scenario when the IP receiver responds to supervision packets.

• Wireless jamming: runs the scenario when the wireless receiver of the panel or one of the two-way transceivers detect

a disturbance on the 868Mhz frequency.

• Wireless jamming restore: runs the scenario when the noise on the 868MHz frequency, detected by the wireless

receiver of the control panel or one of the two-way transceivers, ceases to exist.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ksenia Lares 4.0 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info