Bedienungsanleitung Kyocera km 1500 laser 15ppm (Seite 19 von 76) (Englisch)

435980

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Section 2 NAMES OF PARTS

2-5

(15) Program key & indicator

(Press this key when you want to copy with the Program

function. Make sure that the Program indicator is lit green.)

(16) Add Toner indicator

(This indicator lights red when the toner supply has run low.

See page 8-2.)

(17) Memory Overflow indicator

(This indicator lights red if the memory becomes full during

scanning of originals. See page 7-1.)

(18) Upper drawer indicator

(This indicator lights green when the upper drawer is selected

as the source of paper feed and it flashes green when the

drawer has run out of paper.)

(19) Upper drawer misfeed indicator

(This indicator lights red if a paper jam occurs in the upper

drawer.)

(20) Paper Feeder indicator

(This indicator lights green when the optional Paper Feeder is

selected as the source of paper feed and it flashes green when

the drawer has run out of paper.)

(21) Paper Feeder misfeed indicator

(This indicator lights red if a paper jam occurs in the optional

Paper Feeder.)

(22) Multi-bypass tray indicator

(This indicator lights green when the multi-bypass tray is

selected as the source of paper feed and it flashes green when

the tray has run out of paper.)

(23) Multi-bypass tray misfeed indicator

(This indicator lights red if a paper jam occurs in the

multi-bypass tray.)

(24) Document Processor indicator

(This indicator will light red if an original jam occurs.)

Initial mode (the state that the copier enters at the end of

warm-up or when the Reset/Power key is pressed)

The upper drawer is selected as the source for paper feed, the

number of copies to be made is set to “1” and “Text & Photo” is

selected as the image quality mode.

* If the optional Paper Feeder is installed on your copier, it is

possible for you to change which drawer will be automatically

selected in the initial mode.

* It is also possible for you to change which image quality mode

will be automatically selected in the initial mode.

Auto Clear function

A pre-set number of seconds (between 10 and 270) after copying

stops, the Auto Clear function will automatically engage and the

copier will return to the same settings as those after warm up

(initial mode settings).(However, the copy exposure setting will not

change.) Copies can continually be made using the same settings

(copy mode and number of copies) if the next batch of copying is

started before the Auto Clear function engages.

Auto Drawer Switching function

If two drawers contain the same size of paper and the paper in one

drawer runs out during copying, the Auto Drawer Switching

function will switch paper feed from the empty drawer to the other

drawer that still contains paper so that copying can continue

non-stop.

* The optional Paper Feeder is required in order to use the Auto

Drawer Switching function.

* It is possible for you to turn the Auto Drawer Switching function

OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera km 1500 laser 15ppm Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info