Bedienungsanleitung La Crosse WS-7015 (Seite 10 von 12) (Englisch)

626737

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Caution!

Fast pouring will corrupt the measuring results! Pour the water so slow into the

funnel, that there is no slack water in the funnel at any time.

Recommendation!

In order for the water not to run too fast into the funnel, thus causing a faulty

calibration, place a small cup made of synthetic material into the funnel. Prepare

the cup by piercing a small hole into the bottom using a sharply pointed tool. The

water will now enter the funnel very slowly drop by drop.

Because of the 5.118in (130mm) diameter of the funnel, representing an area of 20.574

(0.0133m

), the amount of 1 Liter of water will yield a nominal rain volume of 2.97 in.

After the entire amount of water has run through the funnel the actual value (displayed

value) will show on the display, in the ideal case 2.96 in.

The ratio of Target Value to Actual Value will yield the Calibration Factor. Since this

calibration factor may have already been entered at an earlier date, it has to be included

in the calculation.

The new Calibration Factor can be computed in the following equation:

Target Value (e.g. 2.96 in) x Old Calibration Factor

New Calibration Factor =

Actual Value (Display after passing 1 Liter of Water)

The old calibration factor can be viewed by simultaneously pressing the

(←

←←

←) and (→

→→

→) keys as well as the "Calibr." Key in Calibration Mode. Select the display

field for the Rain Volume Sensor by use of the (←

←←

←) key.

Correct the calibration factor to its new value by use of the "+" and "–" keys and possibly

the "Fast" key.

By pressing the "Store" key the set value is stored and the display will return to the

normal operating mode.

Change of Units

If the "Units" key is pressed in Calibration Mode, the display section "Rain" will allow the

selection of the units inch or mm and the display section "Air Pressure" will allow the

selection of the units inHg or hPa, and the display section "Indoor temperature“ will

allow the selection of the units ºF or ºC.

Manual Time Setting

To do so press the Arrow (←

←←

←) key twice in Calibration Mode. The display will show time

and date only. Setting is then performed according to Table 1. After entering the time and

date the "Store" key must be pressed.

Table 1: Setting of Time and Date

Function Key

Hours

Minutes

Month Units

Date of Day Sensor

Storing Store

Addressing of Remote Sensors WS 7015-22, WS 7015-28 (optionally) and Remote

Outdoor Sensor

The outdoor sensor concept allows the simultaneous operation of up to 8 outdoor

sensors. Their data are displayed in the upper right display section for the outdoor values.

Each sensor in the system is assigned a sensor address, allowing the receiver to

integrate the sensor into the overall system free from interference. By default the Remote

Outdoor Sensor included in the

shipment is set to be Sensor 1, while

the types WS 7015-22 and WS 7015-

28 are both set to be Sensor 2. The

programmable assignment can be

seen from opposite illustration.

The addressing can be performed by

the user by means of coding bridges

(jumpers) on the wiring side of the

sensor‘s PCB. To do this the protection

hood has firstly to be removed by

unscrewing from the Remote Outdoor

Sensor and then the housing must be

opened by removing the screws on its

back. Both types WS 7015-22 and –28

only need to have their back covers

unscrewed.

Following this the coding bridges can be set according to the addressing table opposite.

Change of Base Address for Sensors with fixed Assignment

Setting of addresses for the Remote Indoor Sensor, Remote Rain Volume Sensor and

Remote Wind Sensor is not required under normal operating conditions.

Multi functional operation is a special feature, allowing to generally operate an arbitrary

number of Base Units within the transmission range of the Remote Sensors. One Base

Station can be placed in the living room, one in the office, etc., all displaying the same

data.

If in every room, in which a Base Station

(Display Unit) has been placed, the indoor

temperature of this particular room needs to

be displayed on the upper left section of the

LCD, then the indoor sensors for

temperature/humidity and air pressure need

to be assigned different base address

according to the illustration opposite.

In order for the Base Station to exclusively

receive its assigned sensor here also a

respective address has to be set. To change

the base address in Calibration Mode the

(←

←←

←)key must be pressed three times and the

desired base address selected by use of the

"Indoor" key.

The base addresses of the Wind Sensor and the Rain Volume Sensor can also be

changed in this operating mode which however is only necessary in very rare cases. A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Crosse WS-7015 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info