Bedienungsanleitung Lenco IPD-5100 (Seite 5 von 40) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

477344

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Fully extend the FM rod antenna for the best FM radio reception.

1. Press the POWER button to turn on the unit, where the power

status indicator light on.

2. Press the FUNC button to select FM stereo or FM mono radio receiving

mode.

3. To manually tune to a desired station, repeatedly press the TUNING

/ button.

4. To automatically search for stations with strong signals, press and hold

the TUNING / button until the frequency digits on display begins to

scan then release the button. The tuner will stop on the first strong

signal it finds.

- Manual tune to select weaker stations that might be skipped during

automatic tuning.

- If the automatic tuning does not stop on the exact frequency of the station,

for example , it stops on 100.9 MHz instead of 100.8 MHz, use the manual

tuning method to "fine tune" to the exact frequency of the desired station.

The units allows you to store up to 20 FM stations for easy recall at any time.

1. Press the POWER button to turn on the unit, where the power status

indicator light on.

2. Press the FUNC button to select FM stereo or FM mono radio receiving

mode.

3. Tune to the radio station you want to store in memory by using the

TUNING button.

4. Press the MEM button. The preset channel number appears on display

and blinking.

5. To select desired preset station number, press the CH button.

6. To confirm preset location, press the MEM button.

7. Repeat steps 3 to 6 to store other stations, if apply.

FM Antenna

Radio Tuning

Radio Preset Stations

Preset Stations

Notes

Radio Tuner Operation

EngEng

This model adopts different iPod models. Following steps guide you

listening to iPod music.

1. Slide the "iPod tilt angle slider" for the "iPod tilt angle lever" to tilt at a

desired angle, if apply. Recommend to lay down the iPod during the

unit transportation.

2. Your iPod can now be inserted into the docking port by placing the

connector on the bottom of the iPod onto connector in the docking bay.

: Please be careful when seating the iPod into the docking to avoid

damaging the 30-pin connector on the iPod or in the docking system.

3. Slightly push the iPod to a desired tilt angle, if necessary.

4. Press the POWER button once to turn on the unit and the power status

indicator lights on.

5. Press the FUNC button to select iPod mode.

In iPod mode :

- To start playback music, press the iPod button once.

To pause the music , press the iPod button.

To resume music , press the iPod button again.

You may press the VOLUME +/- button to adjust the volume to a

desired level.

When a song playback, press and hold the button

perform high speed search forward / backward.

To skip to next or previous song, prese the button.

- To turn off the unit, press the POWER button and the power status

indicator will light off.

- When the unit is powered by external DC adaptor and once the iPod

connected to the docking station, the unit recharges the iPod battery.

Once the iPod is inserted, the unit will switch to iPod mode automatically

and neglect the current mode.

Caution

Note:

Listening to iPod

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco IPD-5100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info