Bedienungsanleitung Lenco IPD-5100 (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

477344

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Clock Setting

When the unit is OFF (power off mode):

1. Press the MODE button and the clock digits blink.

2. Press the CH button to set hour.

3. Press the VOLUME +/- button to set minute.

4. Press the MODE button again entering 12/24 hour format setting mode.

5. Press the button to select 12 or 24 hour display format.

6. To save all settings and auto-exit the setting mode, wait for a few seconds.

Set Clock

Set 12/24 Hour format

Exit setting mode

VOLUME +/-

Listening to an External Audio Source

1. Connect an audio cable (not included) with 3.5mm stereo plug from

an auxiliary audio device to the AUX jack of the unit.

2. Press the POWER button to turn on the unit.

3. To select auxiliary audio input, press the FUNC button. The "AUX"

indicator show on display.

4. Turn on the external auxiliary audio device.

5. The volume and preset equalizer can now be controlled through the unit.

Operate all other functions on the external device as usual.

: Press the POWER button to turn off the unit when you finish listening.

Don't forget to switch off the power of the external audio device as well.

Notes

EngEng

Alarm Operation

When the unit is OFF (power off mode):

1. Press and hold the ALARM button until the alarm source indicator blink.

2. Press the VOLUME +/- button to select alarm source BUZ (buzzer) ,

RAD (radio) or iPod.

3. Press the ALARM button again, alarm time digits blink.

4. Press the CH / button to set alarm hour.

5. Press the VOLUME +/- button to set alarm minute.

6. To save all settings and auto-exit the setting mode, wait for a few seconds.

7. To activate the daily alarm, press the ALARM button and the

corresponding alarm source indicator appears on the LCD display.

---If "Wake to iPod" is selected but your iPod has not been docked, the alarm

source will be redirected to the Alarm Buzzer automatically when the alarm

is reached.

---When "Wake to Radio" is selected, make sure the radio station which you

want to wake to is tuned.

When the alarm time is reached, the buzzer alarm will sound for 3 Minutes.

It goes into Auto-snooze mode if no further button has been pressed.

The display shows the "SNOOZE" indicator. The buzzer turns off for the

snooze time (around 10 minutes) then comes on again. This operation will

be repeated three times. After the fourth alarm is finished, the alarm will

shut off until the same alarm time on the next day.

You may also activate the snooze function manually after the alarm sounds

by pressing the SNOOZE button. The buzzer stops for the snooze time then

comes again.

To cancel the snooze before it expires, press the ALARM button.

The snooze operation (including auto-snooze and manual snooze) can be

repeated by 3 times only.

To stop the alarm immediately after the buzzer sounds, you can also press

the ALARM button. It resets itself for the following day.

Select wake up alarm source

Setting the alarm time

Save settings and activate alarm

Wake to Buzzer

Notes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco IPD-5100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info