Bedienungsanleitung Lenco IPD-5100 (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

477344

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

EngEng

Sleep Timer Function

This feature allows you to fall asleep to the radio or iPod for up to 120 Minutes.

The unit shuts off automatically when the time expires.

1. Press the POWER button to turn the unit on.

2. Either tune to the desired radio station in radio mode or playback music

from the iPod.

3. To select the sleep timer to turn the unit off after 15, 30, 45, 60, 90 or

120 minutes, press the SLEEP button repeately. The display show the

indicator . The unit plays for the selected length of time then

automatically turns off.

4. To turn the unit off before the sleep timer counts down to zero, press

the POWER button at any time.

If you are falling asleep to music from an external device connected to the

AUX input, the sleep timer will shut off the power to this system but it will

not turn off the external device.

Sleep to timer

Notes :

Wake to iPod or Radio

When the alarm time is reached, the selected alarm source (iPod or Radio)

will automatically turn on. It starts softly and gradually becomes louder.

It plays for 30 minutes then shuts off and resets itself for the following day.

During the activation of the alarm source, you may press the SNOOZE

button to activate the snooze function. The alarm stops for the snooze time

(around 10 minutes) then turns on again.

To cancel the snooze before it expires, press the ALARM button.

This manual snooze operation can be repeated three times. Each time the

alarm turns on, it plays for 30 minutes (without pressing the snooze button).

To stop the alarm immediately after the alarm sounds, you may also press

the ALARM button. It resets itself for the following day.

Care and Maintenance

- Do not subject the unit to excessive force, shock, dust or extreme temperature.

- Do not tamper the internal components of the unit.

- Clean your unit with a damp (never wet) cloth. Solvent or detergent should never

be used.

- Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.

- Keep your unit away from heating appliances and sources of electrical noise such

as fluorescent lamps or motors.

If the unit experiences a power surge or electric shock, it is possible that the

internal micro-controller may lock up and the unit will not respond to any

commands from the front panel controls.

1.In this event, unplug and then reconnect the AC power plug into the wall outlet.

2.Use a straightened paper clip, toothpick or similar objects to press the RESET

button located at the rear of the main unit (see the below figure). The reset

operation clears the system memory and all of your previous settings will be

erased.

Resetting the Unit

CAUTION: DO NOT USE SHARP, POINTED OBJECT TO PRESS THE RESET

BUTTON. IT MAY DAMAGE THE RESET SWITCH INSIDE THE UNIT.

RESET button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco IPD-5100 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info