Bedienungsanleitung Lenco LED-4353 (Seite 54 von 231) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch)

793267

Zoom out

Zoom in

Vorherige Seite

1/231

Nächste Seite

English - 15 -

Press OK to store the new frequency for that channel.

Press Back to cancel. This item may not be visible,

depending on whether or not the last watched channel

was analogue.

Clear Channel List: Delete all channels stored in the

channel list of the selected channel installation mode.



OK and press OK button to proceed. Highlight Cancel

and press OK to cancel.

Channel Installation Mode - Cable

Automatic Channel Search: Start a scan for analogue

and digital cable channels. If available, operator op-

tions will be listed. Select the desired one and press

OK. Scan Mode, Channel Scan Type, Frequency

and Network ID options may be available. The options

may vary depending on the operator and the Scan

Mode selections. Set the Scan Mode as Full if you

don’t know how to set up other options. Highlight Scan

and press OK to start the scan. You can press the Back

button to cancel the scan. The channels that have

already been found will be stored in the channel list.

Single RF Scan: Enter the Frequency value. Signal

Level and Signal Quality of the selected Frequency

will be shown. Highlight the Scan option and press

OK to start scan. The found channels will be stored

in the channel list.

LCN: Set your preference for LCN. LCN is the Logical

Channel Number system that organizes available

broadcasts in accordance with a recognizable channel

number sequence (if available).

Channel Scan Type: Set your scan type preference.

Channel Store Type: Set your store type preference.

Favourite Network Select: Select your favourite net-

work. This menu option will be active, if more than one

network is available. This option may not be available

depending on the selected country during the initial

setup process.

Channel Skip: Set channels to be skipped when

switching the channels via Programme +/- buttons

on the remote. Highlight the desired channel/s on the

list and press OK to select/unselect.

Channel Swap: Replace the positions of the two

selected channels in the channel list. Highlight the

desired channels on the list and press OK to select.

When the second channel is selected, the position of

this channel will be replaced with the position of the

LCN option

to 󰀨 or Default in order to enable this feature.

Channel Move: Move a channel to the position of

another channel. Highlight the channel you want to

move and press OK to select. Then do the same for a

second channel. When the second channel is selected,



of that channel. You should set the LCN option to 󰀨

or Default in order to enable this feature.

Channel Edit: Edit channels in the channel list. Edit

the name and channel number of the selected channel

and display Network Name, Frequency, Colour Sys-

tem, Sound System, Modulation and Symbol Rate

information related to that channel. Depending on the

channel other options may also be editable. You can

press the Blue button to delete the highlighted channel.

Analogue Channel Fine-tune: Fine-tune an analogue

channel. A list of available analogue channels will be

displayed. Select the desired one from the list and

press OK button. Then change the frequency of the

channel by pressing Left/Right directional buttons.

Press OK to store the new frequency for that channel.

Press Back to cancel. This item may not be visible,

depending on whether or not the last watched channel

was analogue.

Clear Channel List: Delete all channels stored in the

channel list of the selected channel installation mode.



OK and press OK button to proceed. Highlight Cancel

and press OK to cancel.

Channel Installation Mode - Preferred/General

Satellite/Satellite

Satellite Re-scan: Start a satellite scan beginning

with the operator selection screen for the Preferred

Satellite channel installation mode or with the satellite

selection screen for the General Satellite or Satellite

channel installation mode. When this scanning option



available and thus the preferences you made during

the initial setup process may not be changed.

Satellite Add: Add satellite and perform a satellite

scan.

Satellite Update: Search for any updates by repeating

the previous scan with the same settings. You will also

 If

Channel Installation Mode is set to Preferred Satel-

lite󰀨

the available services. Highlight the satellite and press

OK

Press the Right directional button to proceed.

Satellite Manual Tuning: Start a manual satellite scan.

Favourite Network Select: Select your favourite net-

work. This menu option will be active, if more than one

network is available. This option may not be available

depending on the selected country during the initial

setup process.

Channel Skip: Set channels to be skipped when

switching the channels via Programme +/- buttons

on the remote. Highlight the desired channel/s on the

list and press OK to select/unselect.

Lenco LED-4353 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info