Bedienungsanleitung Lenco SR-03 BT (Seite 4 von 37) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

601657

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

UK-3

3. After the alarm wake-up time is set, you will continue to go for the alarm wake-up mode settings -

repeatedly press the or button for the selections followed by pressing the ALARM button to

confirm, first set the alarm wake-up volume level (01-32), then the wake-up radio station (P01-P10),

and finally the buzzer tone (HI/LO). (F. 6) (F. 7) (F. 8)

4. After the confirmation of the buzzer tone selection, the alarm set up is completed.

5. To check the alarm settings, press the ALARM button once, the alarm wake-up time and the wake-up

mode settings will be displayed one by one in two seconds intervals.

Activating the alarm and the wake-up mode

1. Repeatedly press on the ALARM button to activate the alarm function and select the wake-up mode,

the alarm icon and the corresponding wake-up mode will appear in the display on every press:

“Tuner > USB > Buzzer > OFF > Tuner > USB > … …”.

2. When your desired wake-up mode appears in the display, release the buttons, the alarm function is

now activated and the alarm icon will be displayed. (F. 9)

3. At the selected wake-up time, the selected wake-up mode will be on and the alarm icon in the display

will flash to indicate the alarm is triggered. It will continue for one hour and then shut off

automatically. To stop the alarm sooner, press the button once.

Note: If alarm wake-up to USB is selected and no USB is being inserted or recognized, when the alarm

arrives, the buzzer sound will be activated in place automatically.

Automatic alarm repeat

The alarm will automatically repeat each day at the selected wake-up time as long as the alarm icon is

displayed (alarm function on). To cancel the alarm, repeatedly press the ALARM button until the display

shows “OFF”, and the alarm icon will be disappeared.

Snooze function

During alarm, press the SNOOZE button will temporary switch off the alarm for 5 minutes and the snooze

icon will be displayed. This is repeatable in the one hour alarm duration. (F. 10)

LISTENING TO THE RADIO

When the unit is powered up and switched on for the first time, it will automatically enter into the FM radio

mode. To select radio mode during other operation modes, repeatedly press the MODE button on the front

panel until “TUNER” and the FM frequency are displayed. (F. 11)

Manual tuning

1. To select jog dial manual tuning, first press on the VOLUME/SCROLL control once, then rotate the

same control until you read the correct frequency or the reception is at its best.

2. The display will show the stereo icon if a FM stereo station is received. To select FM mono reception,

press the ►/II button, and the stereo icon will disappear in the display. (F.12)

Automatic tuning

1. Press and hold the VOLUME/SCROLL control for longer than two seconds to scan up or down the

frequency band, it will automatically search for the first station of sufficient signal strength.

2. Repeat the above procedure if you wish to search for another station.

F.4

F.6 F.7

F.5

F.8

F.9 F.10

◀◀

▶▶

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco SR-03 BT Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info