Bedienungsanleitung Lervia KH 4001 (Seite 11 von 20) (Englisch)

601143

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 9 -

Straight stitch

The following types of stitches are defined as straight stitches:

Commencing sewing

1. Position the adjustment wheel of the stitch type selector

such that the

desired number appears in the stitch-type window

. According to the

desired type of straight stitch you must turn the wheel to 2, 3 or 21.

2. Bring the needle into the highest possible position and raise the

sewing foot

3. If nothing has happened: retrieve the lower thread by turning the

handwheel

in an anticlockwise direction and drawing the upper

and lower thread together behind the foot.

4. Lay the fabric, respectively layers of fabrics, to be sewn on the sewing

table under the raised sewing foot

, in such a manner that the need-

le is located approximately 1 cm (3/8“) from the fabric edge and

above the start of the seam.

5. Lower the sewing foot

6. In order to finish off the end of the seam, by sewing backwards, press

the sewing direction reverse switch

as far as it will go and activate

the foot pedal

slightly. Backward sewing is used to combine two

seams as well as to reinforce seams.

7. After finishing sewing backwards change over to sewing in a forward

direction, releasing the direction changeover switch

and briefly

taking your foot from the foot pedal

, then pressing the foot pedal

down once again

Changing the sewing direction

1. Stop the machine at the point where you wish to change the sewing

direction, ensuring that the needle is piercing the fabric.

2. Raise the sewing foot

and align the fabric to the new sewing direc-

tion, whereby you can use the inserted needle as a turning point.

3. Lower the sewing foot

back down and then start sewing in the

new direction.

Finishing the seam

The backwards sewing function is also employed at the ends of the seam

to secure and to reinforce the seam.

1. First sew in the forward mode until you reach the end of the seam,

then stop the machine in this positon using the foot pedal

2. Press the sewing direction reverse switch

, then activate the foot

pedal

in order to sew backwards ca. 1 cm (3/8”) from the edge

or the end of the seam.

Type of stitch No. Stitch length

2 (with needle positioned

on the left)

1–4

3 (with central needle position)

21 (triple stretch stitch) firmly fixed at 2.5

Removing the fabric from the machine

1. Stop the machine.

2. Bring the needle into the highest possible position.

3. Raise the sewing foot

and carefully pull the sewn product out

towards the left.

4. Cut the two threads (Upper and lower threads) with the thread

cutter on the rear of the foot bar.

Take note

The thread cutter is the indentation at the rear of the foot bar. Lay the

thread that is to be cut into the indentation, hold the thread firmly to

left and right of the foot bar and then draw it downwards.

5. To prepare the machine for sewing the next seam, pull approximately

10 cm (4”) from the upper and lower threads through the toes of the

sewing foot

in the direction of the rear of the machine.

Edging seams and stretch materials

• Stitch type No. 2 (simple straight stitch with needle position on the left)

is used to sew hems and light-weight materials.

• Stitch type No. 21 (straight triple stretch stitch) is used to sew stretch

materials.

Sewing in zigzag stitches

Zigzag stitch

Set the stitch type number on the selector wheel

according to the

fixed stitch width of the zigzag stitch. Set the stitch length on the stitch

length selector

It is advisable to sew a few stitches in straight stitch at the beginning

and end of a zigzag seam.

Satin stitch

The satin stitch (a close zigzag stitch, hence with very short stitch lengths) is

achieved when the stitch length selector

is set in the „F“ range. The satin

stitch can be used to sew buttonholes or for decorative purposes. The stitch

width is also here determined from the selected type of stitch or stitch type

number of the respective underlying zigzag stitch. Therefore, first select the

type of stitch you require in accordance with the fixed width and then set

the stitch length on the stitch length selector

within the „F“ range.

Type of stitch No. Stitch length

4 (stitch width 1.5 mm (1/16”))

F-45 (stitch width 3.5 mm (9/64”))

6 (stitch width 5 mm (13/64”))

IB_KH4001_E2719_GB_LB3-6 22.04.2008 16:50 Uhr Seite 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lervia KH 4001 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lervia KH 4001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info