Bedienungsanleitung Lervia KH 4001 (Seite 13 von 20) (Englisch)

601143

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 11 -

Two-fold rampart stitch

This type of stitch is used to sew two pieces of material together if there

are no special requirements in relation to the elasticity of the seams,

e.g. for patchwork.

Set the stitch type selector

at number 11.

Scallop stitch

The machine can create a scallop stitch automatically, which may be

used to decorate the edges of the items you have sewn.

1. Set the stitch type selector

at number 12.

2. Sew the scallop stich closely along the edge of the material.

3. If you wish, you can trim the outer curve of the pattern you have

sewn after you have finished the edge. Make sure you do not cut

through the stitches.

Additional decorative stitches

Both types of stitch may be used for the creation of (edge) decorative

seams as well as smocking.

Set the stitch type selector

at number 13 or 14.

Fishbone stitch

This stitch is used to join two pieces of fabric when a certain space

between the edges or borders is required.

Notice

Use thicker upper and lower threads than is customary.

Type of stitch No. Stitch length

15 (Fishbone stitch) fixed at 2.5 in the factory

Type of stitch No. Stitch length

13 (Random zigzag stitch)

F-1

14 (Pearl stitch)

Type of stitch No. Stitch length

12 (Scallop stitch) F-1.5

Type of stitch No. Stitch length

11 (2-fold rampart stitch) F-3

1. Fold together the edges of the two pieces of fabric to form a narrow

hem, then tack the pieces onto a thin piece of paper, leaving a space

of a few millmeters between the two borders.

2. Set the stitch type selector

at number 15.

3. Sew along the gap, at the same time pulling the upper and lower threads

slightly in order to enable a correct formation of the initial stitches.

4. Remove the attached paper after finishing the sewing and close the

seam by knotting the two threads at the beginning and the end of

the seam on the underside of the material.

Finishing edges

These stitches are used to finish off pieces of fabric to prevent them from

fraying and to hem them in one process. The arrow point stitch is ideal for

finishing off a bed cover or table cloth, for example, whereas the elastic

overlock stitch and the slanted overedge stitch is especially suitable for the

finishing off of stretchable materials.

1. Set the stitch type selector

at 16, 18 or 19.

2. Position the fabric under the sewing foot

so that the line of the

seam (the arrow points of the seam pattern formation) are positioned

ca. 3mm (1/8”) left of the centre of the sewing foot

. This type of

stitch is most effective when the seam line is approximately 6 mm

(1/4”) from the edge of the material, because the stitching movement

extending to the right (right zigzag points) grasps the fabric edge

accurately and thus protects it from fraying.

3. If the distance between the sewing line (arrow points) and edge

should become larger, you can trim the border to the right side

of the seam.

Type of stitch No. Stitch length

16 (Arrow point stitch)

fixed at 2.5 in the factory

18 (Blind hem (open) overlock

stitch)

19 (Elastic overlock stitch)

IB_KH4001_E2719_GB_LB3-6 22.04.2008 16:50 Uhr Seite 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lervia KH 4001 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lervia KH 4001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info