Bedienungsanleitung Lervia KH 4001 (Seite 14 von 20) (Englisch)

601143

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 12 -

Sewing material edges with feather stitch

Use the feather stitch as a decorative border stitch or to hem bed covers,

table cloths and curtains or even for embroidery work.

1. Set the stitch type selector

at 17.

2. Position the fabric with the good side up on the sewing table of

the machine and sew the seam ca. 1 cm (3/8”) from and parallel

to the edge.

3. Trim the fabric close to the seam along the edge.

Besides this, the decorative effect of the feather stitch also prevents the

fabric edge from fraying.

Sewing with three-fold zigzag stretch stitches

This type of stitch can be used to sew heavy stretch materials whenever a

stitch with zigzag pattern is practical. It may also be used as a decorative

edge stitch.

• Set the stitch type selector

at 20.

Sewing buttonholes

Notice

1. It is advisable to practice the sewing of buttonholes on a remnant

of material before you actually attempt this on a garment.

2. If you want to sew buttonholes in soft and yielding materials,

it is adviseable to line the fabric with a stabilising material.

With appropriate practice and suitable settings of the machine, the automa-

tic production of buttonholes in one working process is a simple method

that delivers reliable results.

1. Mark the position of the buttonhole on the material with tailors chalk.

2. Attach the buttonhole sewing foot

(see Chapter „Changing the

sewing foot”) and set the stitch type selector

at 1.

3. Retrieve the lower thread.

4. Lower the sewing foot, so that the markings on the buttonhole foot

align with the chalk markings on the material as shown in the follo-

wing diagram. The front closure of the buttonhole is sewn first.

Type of stitch No. Stitch length/mm Sewing foot

1 (Buttonhole stitch) F-1.5 Buttonhole foot

Type of stitch No. Stitch length

20 (Triple zigzag stretch stitch) fixed at 2.5 in the factory

Type of stitch No. Stitch length

17 (Feather stitch) fixed at 2.5 in the factory

5. Open the caliper on the buttonhole foot

and position the button

to be sewn on between the jaws.

6. Pull the buttonhole lever

down and press it backwards slightly

as shown.

7. Start the machine, at the same time holding the upper thread carefully.

8. Automatic production of the buttonhole takes place in the sequence of

the steps 1 to 4 displayed in the diagram below.

9. Stop the machine when the two side buttonhole seams and the two

finishings of the buttonhole have been completed.

Securing the edges and cutting the buttonhole

1. To secure the edging of the buttonhole, raise the sewing foot

and

turn the material through 90° in an anti-clockwise direction on the

sewing table and then lower the buttonhole foot

once again.

Now sew in straight stitch (Stitch type No. 3) until you have completed

the front fastening of the buttonhole.

2. Remove the material you have sewn from the machine. It is advisable

to insert pins diagonally at both ends of a buttonhole to hinder a sepa-

ration of the stitches.

3. With the thread cutter

cut out the buttonhole, slicing through the

material in the centre between the two buttonhole seams. Proceed

carefully in order to avoid cutting the stitches themselves.

IB_KH4001_E2719_GB_LB3-6 22.04.2008 16:50 Uhr Seite 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lervia KH 4001 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lervia KH 4001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info