Bedienungsanleitung Lervia KH 4001 (Seite 15 von 20) (Englisch)

601143

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 13 -

Fine adjustment during sewing buttonholes

Should the buttonhole seams sewn on both sides of the buttonhole not be

uniform in appearance, a fine adjustment can be undertaken as per the

following method:

1. Set the stitch type selector

at „F“ and, as a test, sew the left-hand

buttonhole seam on a remant of the same material. Observe the

material feed during the process.

2. Should the sewn left-hand buttonhole seam be too coarse or too fine,

appropriately adjust the material feed using the stitch length selector

– left-hand buttonhole seam

– Stitch length

– shorter

– longer

– result

3. When the sewing test has produced satisfactory results for the left-

hand buttonhole seam with regard to the feed, sew a right-hand

buttonhole seam and continue to observe the feed.

4. If the buttonhole seam on the right is too fine or too coarse in compari-

son with the left, adjust the button hole fine adjustment screw at the

rear of the machine housing as described below:

When the buttonhole seam on the right appears to be too coarse, adjust

the screw using the supplied large screwdriver

in the direction marked

„–“; When the right buttonhole seam is too fine, adjust the screw using

the screwdriver

in the direction marked „ +“.

By means of the described method of adjustment it is possible to obtain

a uniform appearance of the two buttonhole seams.

– Stitch length setting wheel

– Fine adjustment screw for sewing buttonholes

– Right-hand buttonhole seam

– Result

Sewing on buttons

1. Measure the distance between the holes of the button and select the

suitable type of stitch with the stitch type selector

in accordance

with the following table:

2. Replace the sewing foot

with the sewing foot for sewing on buttons

(see Chapter „Exchanging the sewing foot”).

3. Position the darning plate

on the stitch plate

of the machine.

The lateral pins of the darning plate

should slide into the holes in

the darning plate

4. Position the button to be sewn on between the foot

and the material

and check that the needle will pierce the left-hand hole in the button

without hitting the button itself. If this is not guaranteed return to step1.

5. Sew approximately 10 stitches at a low speed.

6. Remove the material from the machine. Cut off the upper and lower

threads and knot the two threads underneath.

Sewing in zippers

The zipper foot

is employed to sew in different types of zippers and can

be positioned on the right or on the left of the needle without any difficulties.

If you want to sew in the right side of the zipper, fix the foot shaft at the left

side of the securing pin at the zipper

; If you want to sew in the left side

of the zipper, fix the shaft at the right side of the securing pin.

1. Set the stitch type selector

at 3 and the stitch length

at a value

between 2 and 3.

2. Lower the sewing foot

using the lifting lever

and allow the shaft to

snap on the right or left part of the securing pin on the zipper foot

3. Fold over approximately 2 cm (3/4”) of the material and lay the

zipper under the material.

4. Lower the needle accordingly in the right or the left notch for the

needle in the zipper foot

Type of stitch No. Stitch length/mm Sewing foot

3 2–3 Zipper foot

hole distance of the button Type of stitch No.

1.5 mm (1/16”) 4

3.5 mm (6/64”) 5

5 mm (13/64”) 6

Type of stitch No. Stitch length Sewing foot Miscellaneous

4, 5 or 6 user defined Buttonhole foot Darning plate

IB_KH4001_E2719_GB_LB3-6 22.04.2008 16:50 Uhr Seite 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lervia KH 4001 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lervia KH 4001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info