Bedienungsanleitung Liebherr CBNPes 3967 PremiumPlus (Seite 10 von 26) (Englisch)

597388

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Unscrew

Fig. 15 (56)

the turn hinge

Fig. 15 (55)

Unscrew the bearing element

Fig. 15 (58)

, turn it through

180° and screw it firmly into place again inside.

Carefully lift off the cover on the handle side

Fig. 15 (57)

and

transfer it to the opposite side.

Screw the bottom turn hinge

Fig. 15 (55)

firmly into place

(with 4 Nm) on the new hinge side, possibly using a cord-

less screwdriver.

Re-insert the stopper

Fig. 15 (51)

into the other hole.

Re-insert the bearing pin

Fig. 15 (52)

together with the

washer and adjustable-height foot. In so doing, pay attention

that the locating lug points backwards

4.3.9 Transferring the handles

For appliances without soft stop mechanism (on both

doors):

Transfer the spring clamp

Fig. 16 (71)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp into

place on the new hinge

side until it clicks into

place.

Fig. 16

For all appliances:

Fig. 17

On the bottom door: Lift the stopper

Fig. 17 (70)

out of the

door bearing bush and transfer it.

On both doors: Detach door handle

Fig. 17 (72)

, stopper

Fig. 17 (73)

and pressure plates

Fig. 17 (74)

and transfer to

the opposite side.

When fitting the pressure plates on the opposite side, make

sure they snap properly into place.*

4.3.10 Fitting the lower door

Place the door from above onto the bearing pin

Fig. 15 (52)

Close the door.

Place the plastic cap

Fig. 13 (40)

back on the middle turn

hinge

Fig. 13 (42)

Pass the middle bearing pin

Fig. 13 (41)

through the middle

turn hinge

Fig. 13 (42)

into the lower door.

Appliances with soft stop mechanism:

Attach the washer

Fig. 13 (44)

to the middle bearing pin

Fig. 13 (41)

4.3.11 Fitting the lower soft stop mechanism*

For appliances with soft stop mechanism.

For appliances without soft stop mechanism proceed with

item (see 4.3.12) .

Fig. 18

Remove the cover

Fig. 18 (36)

from the faceplate

Fig. 18 (30)

and re-insert it at the other side.

Engage the joint of the soft stop unit on the hinge side (A)

and swing it into place (B).

The screw holes at the left and right have to register.

Screw the soft stop unit firmly into place(2x Torx® 15)

Fig. 18 (35)

Fig. 19

Attach the faceplate

Fig. 19 (30)

to the soft stop bracket so

that the catches face forwards and the front faces the appli-

ance.

Draw the soft stop bracket

Fig. 19 (34)

to the bearing

element

Fig. 19 (56)

and insert the pin

Fig. 19 (33)

from

above so that the square is seated in the depression.

Attach and engage the cover

Fig. 19 (31)

Pay attention that the cover fits properly so that the door

closes properly and the pin is secured.

Twist the safety lock

Fig. 19 (32)

for removal.

Snap thefaceplate

Fig. 19 (30)

onto the door.

Close the lower door.

4.3.12 Transferring the cable connection

(upper door)

Fig. 20

Using a screwdriver, disengage the cover

Fig. 20 (63)

from

the door.

Detach the connector

Fig. 20 (60)

Putting into operation

10 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CBNPes 3967 PremiumPlus Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CBNPes 3967 PremiumPlus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info