Bedienungsanleitung Liebherr CBNPes 3967 PremiumPlus (Seite 12 von 26) (Englisch)

597388

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What

is more, the door may not close and therefore the appliance

may fail to cool properly.

Screw the turn hinges firmly into place with 4 Nm.

Check all of the screws and retighten if necessary.

4.4 Water connection

WARNING

Danger of electric shock!

Disconnect the appliance by unplugging it before you

connect it to the water line.

Shut off the water supply before you connect the water feed

lines of the IceMaker.

The connection to the drinking water system may be carried

out only by a qualified gas fitter and plumber.

WARNING

Risk of poisoning!

The water quality has to comply with the drinking water ordi-

nance of the respective country (e.g. 98/8

Connect to the drinking water supply only.

The IceMaker serves exclusively for making ice cubes in

household quantities and has to be operated with water suit-

able for the purpose.

Fig. 24

- The water pressure has to be between 0.15 MPa and

0.6 MPa (1.5 bar - 6 bar).

- The water supply to the appliance must be via a cold water

pipe which withstands the operating pressure and complies

with the hygiene regulations.

Use the accompanying stainless steel hose (1.5 m). Do not

reuse old hoses. A 3 m hose is available from the customer

service department and has to be fitted by an expert.

In the hose connecting piece is a sieve with seal.

- Between the hose and the domestic water connection there

has to be a stopcock to interrupt the water supply in case of

need.

- All the fixtures and fittings used for water supply have to

comply with the applicable regulations of the respective

country.

- Do not damage or kink the water inlet pipe when installing

the appliance.

Fig. 25

Connect the straight part of the accompanying stainless

steel hose to the stopcock.

The solenoid valve is at the bottom back of the appliance. It

has a metric R3/4 connecting thread.

Connect the angled part of the stainless steel hose to the

solenoid valve.

Open the stopcock of the water supply and

check that the entire water system is leakproof.

Before initial use:

Have the water pipe bled of air by the proper

expert.

4.5 Insertion into a row of kitchen units

Fig. 26

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2) .

The appliance can be inserted into a row of kitchen units. To

match the appliance

Fig. 26 (2)

to the height of the row of units,

a suitable stack cabinet

Fig. 26 (1)

can be fitted above the

appliance.

Putting into operation

12 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CBNPes 3967 PremiumPlus Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CBNPes 3967 PremiumPlus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info