Bedienungsanleitung Liebherr CT 2931 (Seite 6 von 12) (Englisch)

716889

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

Torx® 15

Torx® 25

Screwdriver

Cordless screwdriver, if necessary

Second person for fitting work, if needed

4.3.1 Detaching the upper door

Note

Remove any food from the door racks before removing the

door, so that no food falls out.

Fig. 5

Pull off the cover

Fig. 5 (1)

forwards and upwards.

Lift off the cover

Fig. 5 (2)

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Unscrew the upper turn hinge

Fig. 5 (3)

(2x Torx® 25)

Fig. 5 (4)

and lift it off.

Lift up the upper door and set it aside.

4.3.2 Detaching the lower door

Open the lower door.

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Unscrew the fastening screws

(11)

(2 x Torx® 25) and pull

the centre bearing block out of the lower door.

Remove plastic washer

(10)

Lift up the door and set it aside.

4.3.3 Transferring the middle bearing elements

Fig. 6

Carefully pull off the covers

Fig. 6 (12)

and fit to the opposite

side.

4.3.4 Transferring the lower bearing elements

Fig. 7

Unscrew fastening screws

Fig. 7 (21)

Remove the lower bearing block

Fig. 7 (23)

, complete with

bearing bolt

Fig. 7 (24)

, washer

Fig. 7 (26)

and adjustable

foot

Fig. 7 (22)

Unscrew the bearing bolt

Fig. 7 (24)

, complete with washer

Fig. 7 (26)

, re-locate it into the mounting hole on the oppo-

site side of the bearing block and tighten again.

Carefully remove the cover plate

Fig. 7 (25)

and re-locate it

to the other side.

Fasten the lower bearing block

Fig. 7 (23)

, complete with

bearing bolt

Fig. 7 (24)

, washer

Fig. 7 (26)

and adjustable

foot

Fig. 7 (22)

to the new hinge side, with the help of a cord-

less screwdriver if necessary, and tighten (with 4 Nm)

once again.

4.3.5 Fitting the lower door

Lower the bottom door onto the bearing bolt

Fig. 7 (24)

Close the door.

Insert the centre bearing block

(13)

turned through 180° into

the lower door and fasten firmly (with 4 Nm)to the new

hinge side with the fastening screws(2 x Torx® 25).

Refit plastic washer

(10)

4.3.6 Fitting the upper door

Set the upper door down on the centre bearing block .

Insert the upper turn hinge

Fig. 5 (3)

in the door on the new

hinge side.

Screw in the upper bearing block tightly (with 4 Nm) (2 x

Torx® 25)

Fig. 5 (4)

. Use a cordless screwdriver if

necessary.

Fit the cover

Fig. 5 (1)

on the opposite side by sliding it rear-

wards and latching it into place.

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CT 2931 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CT 2931

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info