Bedienungsanleitung Liebherr EWTdf 2353 (Seite 5 von 12) (Englisch)

805429

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Setting up

• Avoid positioning the appliance in direct sunlight or near cookers,

radiators and similar sources of heat.

• Standard EN 378 specifies that the room in which you install

your appliance must have a volume of 1 m3 per 8 g of R 600a

refrigerant used in the appliance, so as to avoid the formation of

inflammable gas/air mixtures in the room where the appliance is

located in the event of a leak in the refrigerant circuit. The quantity

of refrigerant used in your appliance is indicated on the type plate

on the inside of the appliance.

Electrical connection

Only operate the appliance with alternating current (AC).

The permissible voltage and frequency are indicated on the type

plate. The position of the type plate is shown in the section entitled

Description of the appliance.

The socket must be properly earthed and protected by a fuse.

The tripping current of the fuse must be between 10 A and 16 A.

The socket must not be situated behind the appli-

ance and must be easily accessible.

Do not connect the appliance using an exten-

sion cable or extension socket.

Do not use stand-alone inverters (conversion

of direct current to alternating/three-phase

current) or energy-saving plugs. Risk of dam-

age to the electronic control system!

Climate rating

The climate rating indicates the room

temperature at which the appliance may

be operated in order to achieve full refrig-

eration performance.

The climate rating is indicated on the

type plate.

The position of the type plate is shown in the section entitled

Description of the appliance.

Climate rating Room temperature

SN +10°C to +32°C

N +16°C to +32°C

ST +16°C to +38°C

T +16°C to +43°C

SN-ST +10°C to +38°C

SN-T +10°C to +43°C

Do not operate the appliance outside the

specied room temperature range.

Switching the appliance on and o

Switching the appliance on

Press the On/O button until the temperature display

lights up.

Switching the appliance o

Keep the On/O button pressed for approx. 3 seconds

so that the temperature display goes out.

Operating and control elements

The electronic control panel has the new "touch capacitance

technology". Any function can be activated by touching the

corresponding icon.

The exact contact point is

between the symbol and its label

(1) Upper compartment temperature display

(2) Lower compartment temperature display

(3) Upper compartment temperature setting buttons

(4) Lower compartment temperature setting buttons

(5) On/O button (switching the appliance on and o)

(6) Audible warning On/O button

(7) Fan switch

(8) Interior light On/O button

Symbols in the display

Alarm (symbol flashes if the temperature inside the appli-

ance is too high or too low)

Demo mode is activated

Setup mode is activated (activating the child lock and

adjusting the display brightness

The interior fan runs constantly

Child lock is activated

The interior light is switched on constantly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr EWTdf 2353 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr EWTdf 2353

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info