Bedienungsanleitung Liebherr K 2834 (Seite 6 von 16) (Englisch)

804842

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Fig. 4

qBefore you connect the appliance, report any damage

immediately to the delivery company.

qThe floor of the installation site must be horizontal and

even.

qDo not install the appliance in direct sunlight, next to an

oven, radiator or similar.

qInstall the appliance with the rear panel up against the

wall and always use the supplied wall spacers (see

below).

qOnly ever move the appliance when it is empty.

qThe surface supporting the appliance must be at the

same level as the surrounding floor.

qDo not install the appliance on your own.

qThe more refrigerant there is in the appliance, the larger

the space that it is installed in must be. If the space is

too small, any leak may create a flammable mixture of

gas and air. For every 8 g of refrigerant, the installation

space must be at least 1 m3. Information regarding the

coolant can be found on the type plate inside the appli‐

ance.

uDetach the connecting cable from the rear of the appli‐

ance, removing the cable holder at the same time

because otherwise there will be vibratory noise!

uRemove the protective film from the decorative trims.

uRemove all transit supports.

To achieve the specified energy consumption, use the

spacers, which are supplied with some appliances. This

increases the appliance depth by approx. 35 mm. The

appliance will work properly without the spacers but will

consume slightly more energy.

uIf your appliance comes with

wall spacers, mount these on

the back of the appliance,

bottom left and right.

uDispose of packaging material (see 4.5 Disposing of

packaging) .

CAUTION

Risk of injury or damage from the appliance tipping or the

door falling open!

If the additional adjustable foot on the base support is not

correctly positioned on the floor, there is a risk of the door

falling open or the appliance tipping. This can lead to injury

or property damage.

uUnscrew the additional adjustable foot on the support

until it reaches the floor.

uThen turn it another 90°.

uAlign the appliance so that it

stands firmly and on a level

by applying the accompa‐

nying spanner to the adjust‐

able-height feet (A) and

using a spirit level.

uThen support the door:

Extend the adjustable foot

at the turn hinge (B) until it

rests on the floor and then

make a further 90° turn.

Note

uClean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

uAlways see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

qTorx 20

qTorx 15

qScrewdriver

qIf necessary, cordless screwdriver

qSecond person for fitting work, if needed

4.3.1 Removing the door

Note

uRemove any food from the door racks before removing

the door, so that no food falls out.

Fig. 5

uRemove the spacer Fig. 5 (13) from under the left-hand

side of the door.

Fig. 6

uPull the cover Fig. 6 (1) forwards and upwards.

uLift off the cover Fig. 6 (2).

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr K 2834 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr K 2834

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info