Bedienungsanleitung Liebherr K 2834 (Seite 7 von 16) (Englisch)

804842

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

CAUTION

Risk of injury if the door tips!

uTake good hold of the door.

uSet down the door carefully.

uUnscrew top bearing block Fig. 6 (3) (2x Torx® 20)

Fig. 6 (4) and lift off in upward direction.

uLift out the door and set aside.

4.3.2 Change freezer compartment door

Fig. 7

uFold away cover of turn hinge Fig. 7 (15).

uUnscrew turn hinge Fig. 7 (15) together with compartment

door.

uUnscrew closing element Fig. 7 (16).

uClose the vacated holes with the accompanying stoppers

Fig. 7 (17).

Fig. 8

uFit closing element Fig. 8 (16).

uFit compartment door at the top.

uFit turn hinge Fig. 8 (15) and fold the cover.

4.3.3 Relocating the bearing components

Fig. 9

uUnscrew fastening screws Fig. 9 (21).

uRemove the lower bearing block Fig. 9 (23), complete with

bearing bolt Fig. 9 (24), washer Fig. 9 (26) and adjustable

foot Fig. 9 (22).

uUnscrew the bearing bolt Fig. 9 (24), complete with

washer Fig. 9 (26), re-locate it into the mounting hole on

the opposite side of the bearing block and tighten again.

uCarefully remove the cover plate Fig. 9 (25) and re-locate

it to the other side.

uScrew on the lower bearing block Fig. 9 (23), complete

with bearing bolt Fig. 9 (24), washer Fig. 9 (26) and adjust‐

able foot Fig. 9 (22) to the new hinge side, with the help

of a cordless screwdriver if necessary, and tighten (with

4 Nm) once again.

4.3.4 Transferring the handle

uLift the stopper Fig. 10 (30) out of the door bearing bush

and transfer it.

Fig. 10

uDetach door handle Fig. 10 (31), stoppers Fig. 10 (32) and

pressure plates Fig. 10 (33) plates and transfer to the

opposite side

uWhen fitting the pressure plates at the opposite side, pay

attention that they engage properly.

4.3.5 Fitting the lower door

uLower the door from above onto the bearing bolt

Fig. 9 (24).

uClose the door.

uInstall the upper bearing block Fig. 6 (3) on the new hinge

side and in the door.

uScrew in the upper bearing block tightly (with 4 Nm)

(2x Torx® 20) Fig. 6 (4). Use a cordless screwdriver if

necessary.

uSlide on the cover Fig. 6 (1) on the opposite side from the

outside and snap it into place.

uSlide on the cover Fig. 6 (2) on the opposite side from

above until it snaps into place.

uUnscrew the adjustable foot Fig. 9 (22) on the lower

bearing block Fig. 9 (23) until it touches the floor.

Fig. 11

uInsert the spacer Fig. 11 (13) back under the right-hand

side of the door, as this is important for the stability of

the appliance.

WARNING

Danger of injury due to door falling out!

If the bearing parts are not screwed on tightly enough, the

door may fall out. This can result in serious injuries. In

addition, the door may not close with the result that the

appliance does not cool properly.

uScrew the bearing brackets on firmly with 4 Nm.

uCheck all screws and retighten them if necessary.

Putting into operation

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr K 2834 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr K 2834

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info