Bedienungsanleitung Linksys E2500 (Seite 40 von 80) (Englisch)

461757

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Setting Up: Advanced

Linksys E-Series

How to enable Voice over IP on your

network

Do I need to configure Voice over IP? VoIP (Voice over Internet Protocol) is a

technology for using the Internet as an interface for telephone communications.

To use VoIP, you need to get an account with a VoIP service provider. The VoIP

service provider typically provides you with a telephone adapter (TA) that

connects to your network. If you do not use your network to make phone calls,

you don’t need to change the default settings.

The SIP (Session Initiation Protocol) ALG (Application Layer Gateway) feature

allows SIP packets, used by some VOIP service providers, to traverse (go

through) your router’s firewall.

To configure the router for VoIP:

Administration > Management

Log into the browser-based utility (see “How to open the browser-based

utility” on page 21).

Click the Administration tab, then click the Management page.

If your VoIP service uses SIP, select Enabled next to SIP ALG.

– OR –

If your VoIP service uses other NAT traversal solutions such as STUN

(Session Traversal Utilities for NAT), TURN (Traversal Using Relay NAT), or

ICE (Interactive Connectivity Establishment), select Disabled (default).

NOTE

You may need to contact your VoIP service provider to determine

the type of NAT traversal configuration they use.

How to configure UPnP

What is UPnP? UPnP (Universal Plug and Play) allows devices connected

to a network to discover each other and automatically create working

configurations. Examples of UPnP-capable devices include web cameras,

online gaming applications, and VoIP devices. UPnP is enabled by default.

To configure UPnP:

Administration > Management

Log into the browser-based utility (see “How to open the browser-based

utility” on page 21).

Click the Administration tab, then click the Management page.

To use UPnP, select Enabled (default) next to UPnP. Otherwise, select

Disabled.

To allow changing router settings while using UPnP, select Enabled

(default) next to Allow Users to Configure. Otherwise, select Disabled.

To prevent local network users from disabling your Internet connection

through UPnP, select Disabled (default) next to Allow Users to Disable

Internet Access. Otherwise, select Enabled.

How to use a router as an access point

How can I use my old router as an access point? If you have a large area to

cover with your wireless signal, or if part of your home has weak signals due to

interference, you can use your old router to extend the range of your wireless

network. This is a complex process, so this procedure assumes that you have

some networking knowledge.

TIP

Check the documentation for your old router. Some brands of

routers include either a switch on the outside of the case or a

software option to convert it to an access point. If either of these

options is available, follow your old router’s instructions to convert

it to an access point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys E2500 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys E2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info