Bedienungsanleitung Linksys E2500 (Seite 43 von 80) (Englisch)

461757

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Setting Up: Advanced

Linksys E-Series

To determine the address range by using a Mac computer:

Connect your computer into your upstream network’s router.

From the Dock, click System preferences, click Network, then click

Ethernet in the window to the left. A network status window appears.

Take note of the IP address. In this example, the IP address is

192.168.100.139.

Example: The above examples show that upstream IP addresses are on

the 192.168.100.0 network. (The “0” indicates the entire network.) Your

upstream network’s address may be different. The default address of

your new Linksys router is 192.168.1.1. In setting up one router behind

another, you must make sure that the local network on your new router is

different than the network of your upstream router. In the above example,

because the default local network on your Linksys router 192.168.1.0 is

on a different subnet than the office network’s 192.168.100.0, you will be

able to place your Linksys router behind the other router.

Connect an Ethernet network cable to a LAN/Ethernet port on your

upstream network to the yellow Internet port on your router.

CAUTION

Connect the upstream network to your router’s yellow Internet

port, not one of the blue Ethernet ports. If you connect to an

Ethernet port, you create IP addressing problems for the office

network.

TIPS

An office network often has a wall plate with an Ethernet port that

you can connect to.

If you are doing this in a home environment (without wall ports),

connect an Ethernet network cable between a LAN port on your

upstream router and the Internet port on your Linksys router.

Run Cisco Connect on each computer that you want to connect to

the Linksys router. Each computer needs either a wired or wireless

connection to the Linksys router. For more information, see “How to

connect a computer to your network” on page 13.

The computers that are connected to the Linksys router are now on the same

network, and are isolated from the upstream network. However, you will still

have access to the Internet through the upstream router (by way of your Linksys

router). Because two routers are between your computer and the Internet,

Internet traffic undergoes two network address translations. This is sometimes

referred to as Double NAT.

Your computers can also use the built-in capabilities of your Linksys router,

such as parental controls. If you need further control over the type of content

your employees or family access, you can create an account with an Internet

filtering site such as www.opendns.com or www.bsecure.com. After you

create an account with them, use their DNS in place of your ISP’s DNS.

To use their DNS:

Setup > Basic Setup

Log into the browser-based utility (see “How to open the browser-based

utility” on page 21).

Click the Setup tab, then click the Basic Setup page.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys E2500 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys E2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info