Bedienungsanleitung Linksys E900 (Seite 48 von 92) (Englisch)

590197

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Setting Up: Advanced

Linksys E-Series

How to use a router as an access point

How can I use this new router as an access point? If you have a large area to

cover with your wireless signal, or if part of your home has weak signals due to

interference, you can use this router to extend the range of your old router’s

wireless network.

For ALL

To set up your new router as an access point:

Setup > Basic Setup

Use a network cable to connect this router’s Internet port to the Ethernet

or LAN port on the router that is connected to your modem.

Log into the browser-based utility (see “How to open the browser-based

utility” on page 25).

Click the Setup tab, then click the Basic Setup page.

For Internet Connection Type, select Bridge Mode.

Click Save Settings to apply the changes. The new router’s LAN IPaddress

will be changed and obtained from the router that is connected to your

modem.

IMPORTANT

While in Bridge Mode, the following browser-based utility pages

will be unavailable:

•Setup tab: IPv6 Setup, DDNS, MAC Address Clone, Advanced

Routing

•Security tab: all pages

•Access Restrictions tab: all pages

•Applications & Gaming tab: all pages

•Administration tab: Log

For ALL

How can I use my old router as an access point? If you have a large area to

cover with your wireless signal, or if part of your home has weak signals due to

interference, you can use your old router to extend the range of your wireless

network. This is a complex process, so this procedure assumes that you have

some networking knowledge.

TIP

Check the documentation for your old router. Some brands of

routers include either a switch on the outside of the case or a

software option to convert it to an access point. If either of these

options is available, follow your old router’s instructions to convert

it to an access point.

You need to take note of your new router’s settings, then apply some of those

settings to the old router so it can work as an access point.

To view your new router’s settings:

Wireless > Basic Wireless Settings (non-E4200)

Wireless > Wireless Security (non-E4200)

Wireless > Wireless Settings (E4200)

Status > Wireless Network

Setup > Basic Setup

Make sure that your new router is connected to the Internet.

In the browser-based utility, click the Wireless tab

For the E4200, click Wireless Settings and take note of the Network

Name (SSID), Security Mode, and Passphrase.

Or, for other Linksys router models:

Click the Basic Wireless Settings page and take note of the Network

Name (SSID).

Click the Wireless tab, then click the Wireless Security page and

take note of the Security Mode and the passphrase.

Click the Status tab, then click the Wireless Network page and take note

of the Channel.

Click the Setup tab, then click the Basic Setup page and take note of

the DHCP server’s IP Address range (192.168.1.100 to 192.168.1.149 by

default)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys E900 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys E900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info