Bedienungsanleitung Linksys E900 (Seite 50 von 92) (Englisch)

590197

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Setting Up: Advanced

Linksys E-Series

To add your router to an existing router or gateway

In most cases, you can easily add your router to an existing wireless network by

running Cisco Connect. If you are unable to set up the additional router using

the instructions below, see “To share an Internet connection” on page38 or “To

extend your network” on page39.

To add a router to your existing wireless network:

Insert the Cisco Connect setup CD into a CD/DVD drive on your computer,

then follow the on-screen instructions.

When you are told to connect your router’s Internet port to the LAN/

Ethernet port on your modem, connect your router’s Internet port to

the LAN/Ethernet port on your existing (upstream) router or gateway.

Follow the on-screen instructions until setup is complete.

To share an Internet connection

NOTE

This is a complex process, so this procedure assumes that you have

some networking knowledge.

To add another router to share an Internet connection:

This topic covers cases one and two above

Determine the IP address range for your upstream (office or building)

network.

To determine the address range by using a Windows computer:

Connect your computer into your upstream network’s router.

Click Start, Run, type CMD, then click OK. The command prompt

window appears.

Type ipconfig, then press Enter.

TIP

Although you can determine your computer’s IP address in many

ways, this method is very fast.

Take note of the IP address. In this example, the IP address is

192.168.100.192.

To determine the address range by using a Mac computer:

Connect your computer into your upstream network’s router.

From the Dock, click System preferences, click Network, then click

Ethernet in the window to the left. A network status window appears.

Take note of the IP address. In this example, the IP address is

192.168.100.139.

Example: The above examples show that upstream IP addresses are on

the 192.168.100.0 network. (The “0” indicates the entire network.) Your

upstream network’s address may be different. The default address of

your new Linksys router is 192.168.1.1. In setting up one router behind

another, you must make sure that the local network on your new router is

different than the network of your upstream router. In the above example,

because the default local network on your Linksys router 192.168.1.0 is

on a different subnet than the office network’s 192.168.100.0, you will be

able to place your Linksys router behind the other router.

Connect an Ethernet network cable to a LAN/Ethernet port on your

upstream network to the yellow Internet port on your router.

CAUTION

Connect the upstream network to your router’s yellow Internet

port, not one of the blue Ethernet ports. If you connect to an

Ethernet port, you create IP addressing problems for the office

network.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys E900 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys E900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info