Bedienungsanleitung Livin Flame Zurich (Seite 12 von 24) (Deutsch, Englisch, Holländisch, Französisch)

742180

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENG-6

Maintenance

Warning: Before any maintenance and/or cleaning the exterior of the ﬁreplace, disconnect the unit from

the power supply and leave until cooled off.

Remote Handset Battery Replacement: This remote control uses 1 CR2032 Lithium lon button cell battery

(Included). Make sure the batteries are installed correctly in the remote control.

This product does not use a standard bulb for its ﬂame effect. The appliance uses an electronically

controlled LED system to create the effect therefore no parts need to be replaced. There are no

user-serviceable parts on this appliance. Under no circumstances should the appliance be serviced by

anyone other than a qualiﬁed electrician.

Resetting the Thermal Cutout Switch: The appliance is ﬁtted with an Electronic Safety Control (E.S.). This is

a safety device, which switches off the ﬁre if, for any reason, the appliance overheats, e.g. when covered. If

the heater stops operating whilst the ﬂame effect continues normally, this indicates that the E.S. Control is

in operation. The E.S. Control can only be re-set after the appliance has cooled down, in order to re-set the

E.S. Control proceed as follows:

- Switch off the appliance (Manual On/Off switch) and leave for approximately 10-15 minutes.

- Remove any obstruction to the fan heater outlet or fan blades etc. Make sure that the power

supply is disconnected at the plug socket outlet whilst you do this.

- Switch on appliance and the E.S. Control will re-set.

- Ensure that the appliance is functioning correctly.

Cleaning the ﬁreplace

The area around the ﬁre should be kept free of any materials such as lint or house dust (i.e. animal hair/

carpet ﬁbres) that could be drawn into the internal workings of the appliance and hence affect the

performance. We recommend that you clean around the fan grille housing at regular intervals. This can be

done using standard vacuum cleaner and suitable attachment. You can clean the outside of the appliance

with a suitable cloth. Do not use furniture or metal polish.

The fuelbed can be dusted as required with the appliance off.

Warning: An authorized service representative should perform any other servicing.

Warranty

Your ﬁreplace has two year warranty against manufacturing defect, beginning at the date of purchase.

In case of a problem, contact the store that it sold to you.

Warranty will be honored when you present a dated invoice and is strictly limited to recognized faulty part.

Installation costs cannot, under any circumstance, be reimbursed for damages.

The manufacturer can’t be held responsible for direct or indirect defect consequences, either towards

person or property.

The warranty will be voided if the ﬁreplace was misused or used for other purpose than what they were

built for. The warranty will also be voided in case of deterioration or accident that occur following neglect,

bad supervision or form altered parts.

Technical speciﬁcations

Voltage:

Heating Element:

Dimensions:

Illumination:

220V-240V~ 50Hz

1800 - 2000W

425mm H x 580mm W x 190mm D

LED system (no replaceable parts)

Gimeg Nederland Strijkviertel 27 3454 PH de Meern, The Netherlands

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Livin Flame Zurich Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info