Bedienungsanleitung Loewe bild 9.65 (Seite 207 von 227) (Englisch)

691477

207

Zoom out

Zoom in

Vorherige Seite

1/227

Nächste Seite

Loewe bild

User handbook

207

Problem Possible Cause Remedy/notes

In the case of TV sets with an integrated hard

disk, this is sometimes not recognized when

switched on

Data errors on the hard disk can lead to this

being not recognized correctly when the TV

set is started. As a rule, the TV performs a

test of the internal hard disk itself.

To prevent damage to the hard disk, always

switch the TV set to standby first, before

disconnecting it from the power supply with

the mains switch or a switched socket strip.

The check of the hard disk can be started

manually via the menu (System settings ט

Control טmore… טHard disksטCheck

integrated one.

If this is not successful, you can via the menu

item Format integrated one completely

delete the internal hard disk.

ATTENTION: Thus all data are lost. A data

recovery is not possible in this case.

Observe the point of the data backup in the

Chapter Recordings, section Digital

Recorder – Delete manager.

General problems on connecting External

devices via an AV Input.

The signal type is set incorrectly. Set the signal type correctly (System set-

tings ט Connections ט AV connecting

settings ט Signal type).

If the Signal Type is set to “Automatic” this

can lead to error recognitions in the case of

non-standardised signals. Then the standard

and signal must be adjusted according to the

specifications in the manual of the external

device.

With Teletext different characters are dis-

played incorrectly.

The wrong character set is set in the System

settings .

Set the correct character set: System set-

tings ט Control ט more ... ט Standard

Teletext ט Character set ט Standard

the corresponding character set.

There are errors on the operation of a CA

module.

Switch the TV set off. Remove the CA module

from the TV set. Wait a few seconds. Reinsert

the CA module. Turn the TV set back on.

The TV set does not accept CI + modules,

although these are detected in another set.

Check whether in the menu System settings

ט Extras ט Integrated features under the

menu item Hardware, PRODUCTION is

listed with CIPlus.

Contact your specialist dealer.

I have two CA modules in the set but never-

theless cannot simultaneously record and

view another program.

The setting for the rights of both CA modules

is incorrect.

Select for the CA modules in the menu

System settings ט Extras ט <Name of

the CA Modules> ט Smartcard Rights the

option Same Rights.

The option must be selected for both CA

modules.

When the set is switched on, a message from

the CA module appears every time that it is

authenticated.

CI+ modules must be authenticated in the TV

set. Both sets thereby exchange the safety

information.

When using a CA module for the first time,

this authentication may take some time de-

pending on the module.

A shorter version of the authentication is

performed at each switch on. This is depend-

ent on the module speed and is hidden by the

start process of the TV device or possibly

leads to a message which can not be pre-

vented.



Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe bild 9.65 Seite 207

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe bild 9.65

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info