Bedienungsanleitung Logitech z-5500 (Seite 6 von 23) (Englisch, Französisch)

227344

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

• Stereo x2: Send the Dolby® Digital stereo, PCM stereo, or L/R analog 2 channel stream to both the front and rear

speakers without applying any decoding algorithm.

WHAT IT IS: This effect will send the stereo audio to the rear speakers, creating front and rear stereo sound (much

like a car stereo).

• Stereo: Send the Dolby® Digital stereo, PCM stereo, or L/R analog 2 channel stream to the front speakers only

without applying any decoding algorithm.

WHAT IT IS: This effect will send the stereo audio to the front speakers only.

Adjusting Volume and Other Levels

To adjust the main volume, simply rotate the knob.

To adjust your trim levels for the subwoofer, center channel, or the surround (rear) speakers, press the ‘level’ button to cycle

through them. For each one, rotate the knob to adjust the level. Note that each level setting is a “global” setting, meaning

that the levels will remain the same regardless of what input or effect is selected.

The LCD will return to its previous state if left alone for 5 seconds.

Volume Boost feature: A volume boost feature is available for source material that is recorded at anbormally low levels.

When the volume is at maximum, continue spinning the knob approximately one-half turn (180 degrees) clockwise. The

LCD will show “Boost” and a number. You are now in volume boost mode. Adjust the volume boost just llike you would the

system volume. When at Boost 1, spinning the knob to the left will return to normal volum mode. You may also access the

volume boost mode using the remote by holding down the volume up button when the normal volume is at maximum.

Note that boost mode should not be used with source material that is already recorded at high levels. Doing so will cause

your speaker system to distort signiﬁ cantly – and will eventually damage it. Damage caused by improper use of boost

mode is not covered by the manufacturer’s warranty.

Headphones

When the headphones are plugged in, the speakers will mute and all sound will go to the headphones. The LCD will display

‘Headphones’ as the active effect. Only a stereo signal will go the headphones, regardless of the input or surround sound

effect. When listening to material with surround sound content, the audio will be “downmixed” so that all the sounds are

heard in the headphones. When the headphones are unplugged, the speakers will automatically return to their previous

state.

Wall-Mounting

Your speakers are equipped with a notch for wall mounting. Rotate stands 180°. Use appropriate wall screws and posts to

secure each speaker to your wall.

Muting the Speakers

To mute the speakers, simply press the mute button. The speakers will be muted and the control pod LCD will display ‘Mute

On’. The speakers will remain Muted until any of the following occur:

• ‘Standby’ button is pressed. Speakers go into standby mode.

• ‘Mute’ button is pressed again. The speaker volume returns to previous volume level and speakers go to Ready state.

• ‘Level’, ‘input’, ‘effect’, or ‘settings’ button is pressed. The speaker volume returns to the previous level and the

product performs the appropriate action for the button that was pressed.

• Control knob is rotated. Disengages mute and adjusts Main volume.

• ‘TEST’ button is pressed on the remote. Puts system in Test Mode.

Changing Surround Sound Settings

To change the surround sound settings, press the ‘settings’ button. Not all settings are available for each effect (see table

below). If the active effect does not have changeable settings, then the LCD will show ‘No settings for this effect’.

Cables

• Satellites:

– L / R cord length: 15’ (4.5m)

– C cord length: 15’ (4.5m)

– LR / RR cord length: 25’ (7.5m)

• Cables:

– 7’ 3-pair cable with (3) 3.5mm Male stereo connectors on each end – color-coded to match the jacks on the

control pod

• Subwoofer:

– Control pod connection: Female DSUB jack

– Powered connections to all 5 satellites: RCA jacks

• Subwoofer connection (carries all 6 ‘power-in’ signals): 7’ DSUB cable

Operation

EFFECTS

SETTING

DTS®

DIGITAL

5.1

DOLBY®

DIGITAL

5.1

PRO

LOGIC II

MOVIE

PRO

LOGIC II

MUSIC

6 CHANNEL

DIRECT

STEREO

STEREO HEAD-

PHONE

Panorama



Dimension



Center Width



Surround Delay

 

Night Mode



Table 2 - Available Settings for Each Effect

English

Z-5500d_manual_AMR.indd 10-11Z-5500d_manual_AMR.indd 10-11 3/23/05 3:49:07 PM3/23/05 3:49:07 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Logitech z-5500 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Logitech z-5500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info