Bedienungsanleitung Lorenz STARLIGHT PRO (Seite 74 von 108) (Englisch)

757006

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

76 User Manual

nominal range, the light of the Nav-Aid will start blinking.

'MENU' + "MAP SETTINGS" +'ENTER' + "Dynamic Nav Aids" + 'ENTER'

Display Mode

To simplify the customization of the chart display, the map settings are now re-organized in modes

allowing the user to choose the preferred setting. Pre-programmed settings are user selectable from

Full, Medium, Low, Radar, Tides, Custom. The default setting is Custom.

'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER' + "Display Mode"

+ 'ENTER'

Distance (Track)

When the tracking function is On and the type of track storing is Distance, you can store a fix when the

distance from its last stored position is greater than a defined distance. Choose in the range 0.01, 0.05, 0.1,

0.5, 1.0, 2.0, 5.0, 10.0 Nm (the distance unit is selected by the user). The default setting is 0.01 Nm.

'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "DISTANCE" + 'ENTER'

Distance (Unit)

Sets the distance unit among Nm = nautical miles, Sm = status miles e Km = kilometers. The default

setting is Nm.

'MENU' + "BASIC SETTINGS" + 'ENTER' + "DISTANCE" + 'ENTER'

DTG = Distance To Go

The actual distance to reach the Target.

EBL = Electronic Bearing Line

Dotted line with direction selectable by the user (see Par. 4.3).

Select Advanced Mode + 'ENTER' + "EBL & VRM" + 'ENTER'

Echosounder AVAILABLE ONLY IF THE CHARTPLOTTER IS CONNECTED TO THE

VOICE NAVIGATION SYSTEM

Enables (On) or disables (Off) the Echosounder C-Voice mode. If it is On, the Depth message is spo-

ken. The message is spoken if a valid depth data is received by the chartplotter or if it is in Simulation

mode. The default setting is Off.

'MENU' + "BASIC SETTINGS" + 'ENTER' + "C-VOICE" + 'ENTER' + "ECHOSOUNDER" + 'EN-

TER'

Event

User point that refers to the ship's position. It is simply a way of marking where the boat is (see Par.

4.2). An existing Event can be connected to the current route.

Inserting Event: 'CLEAR' + 'EVENT'

Deleting Event (Advanced Mode): Place cursor on Event + 'ENTER' + "DELETE" + 'ENTER'

Deleting Event (Basic Mode): Place cursor on Event + 'CLEAR'

Editing Event: Select Advanced Mode + Place cursor on Event+ 'ENTER' + "EDIT"+ 'ENTER' + Modify

Symbol, Name, Color + 'CLEAR'

Add to Route: Select Advanced Mode + Place cursor on Event+ 'ENTER' + "ADD TO ROUTE" + 'EN-

TER'

External Alarm

Allows triggering an external alarm device. You can enable (On) or disable (Off) the External Alarm.

The default setting is On.

'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' + "EXTERNAL ALARM"

+ 'ENTER'

External Waypoint

The coordinates of a Waypoint, received from a GPS or a LORAN connected to the chartplotter, can

be stored into the chartplotter, if the GPS or the Loran are NMEA-0183 protocol compatible and

support the $BWC sentence (this symbol remains on the screen for 30 seconds). You may save it by

placing a Waypoint or a Mark onto that symbol. As soon as the chartplotter receives another $BWC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lorenz STARLIGHT PRO Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info