Bedienungsanleitung Lowrance X-15 (Seite 6 von 14) (Englisch)

599332

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

back of thin

fiberglass

panels

support

the

X-15.

If the

desired location is closer

than 18"

to a

magnetic compass,

a trial run

should be made with

the unit in

operation

to be sure

that the

compass

readings

are not

affected.

Figure

_________________

BE SURE

to insert the two rub-

ber

grommets

gimbal

bracket.

The

larger

side

(larger diameter)

grommet goes

on inside of

gimbal

bracket so

that it is sand-

wiched between

gimbal

bracket

and sonar instrument

(see

draw-

ings).

The

grommets provide

fric-

tion to hold the unit at

the desired

angle.

Power Connections

—

Twelve volt DC

power

for

the

depth

sounder should

supplied

the boat's 12-volt

electrical

sys-

tem.

The

power

cable

may

be at-

tached to an

accessory

power

buss,

but if

you

have

problems

with

electrical

interference,

the

cable

should be attached

directly

to the

battery.

If a

longer

cable is

required,

use

ordinary

#18

lamp

cord available

any

hardware or electronic

sup-

ply

store.

Splices

should be sol-

dered. If this can't be

done,

use

crimp-type splices. Tape

all

splices

with

electrical

tape.

in-line fuse

holder with fuse

supplied

with the

X-15. Be cer-

tain to

install this fuse holder

to the

power

source

pos-

sible. This will

protect

both the

sonar unit

and the

power

cable in

the event

a short occurs.

Crimp

connectors

are

supplied

to attach

the fuse

holder to the

power

ca-

ble. The red

or white wire in the

power

cable is

the

positive

con-

ductor. The

black wire is the

ground

conductor

The

graph

protected

from

ac-

cidental

polarity

reversals and no

damage

will occur if

the wires are

reversed. The unit

will not

operate,

however,

until the

proper polarity

applied.

Transducer Selection

Lowrance offers

you

the choice

transducers with

either an 8

degree

cone

angle

or 20

degree

cone

angle

that will

interchange

with

any

our 192 kHz sonar

units. In

other

words,

any

Low-

rance

sonar instrument can be

used with

any

Lowrance trans-

ducer of

the same

frequency

with-

out

retuning

any kind,

and no

loss of

performance.

However,

the

use of

any

other manufacturer's

transducer will result

in a loss of

performance.

Now

you

can

select the trans-

return the unit to the

control

of the

micro-computer, simply

press

0 and

then the LINES and

SCALES

keys

at the same time.

This will revert

the unit back to

normal

operation.

Example:

Set the initial transmitter

pulse

width

tolOO

micro-seconds.

Press:

1,0,

0, then SCALES and

LINES

together

Result:

Figure

Example:

Set the initial

transmitter

pulse

width

to5O

gs.

Press:5,

then SCALES

and

LINES

together.

Result:

Figure

'ii.

•

'•.•

A':

I :\'

'Ii

Figure

Ground

(Negative)

Figure

Qosci Iii

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lowrance X-15 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info