Bedienungsanleitung Lynx Aurora LT-TB (Seite 31 von 55) (Englisch)

587002

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

The Output label appearing in green indicates that this is the Selected

Output. A different Output can be selected by clicking a different

pair’s Output button. In this state, any of the Sources in the Input

Section can be routed to this output. For instance, if we have an input

signal on Analog In 3, and we wish to hear it through Analog Out

1+2, Select Analog Out 1+2 in the bottom of the Outputs Section,

then un-mute Analog In 3 in the Inputs Section. Now signals from

Analog Input 3 will be heard through Analog Output 1. If we would

like to hear the signal through Analog Outputs 1+2 both, then the Pan

Knob can be used to pan Analog In 3 to the center, or anywhere

within the stereo spectrum.

By default, Odd number inputs are panned to the left, and Even number to the right.

 Numeric Level Indicator

This displays the amount of attenuation performed on the associated record source. This is

attenuation for the Monitor level of the signal; it has NO bearing on the level being recorded

through an audio application. It is applicable to Monitoring Level only (how loud that signal

source is through the output you are listening to).

 Faders and Meters

The METERS on the Input section show the level strength of the signals at the

associated input. Since there is no way to attenuate the level of the signal being

recorded (except for the Trim controls, or the Trim Pots on the Aurora 16-VT),

the METER level will reflect the signal that will be recorded into audio

software. The METER will not reflect attenuation to the input signal as it is

being monitored. When you lower the fader, the METER level will not change,

however the change WOULD be reflected in the meters of the output this signal

was routed to.

The FADERS are for attenuating the signal of the input as it is being hardware

monitored. For instance, if you are routing a signal from Analog Input 5, through

Analog Output 3+4, and the input signal is too loud relative to the rest of the mix, you would

lower the fader under AIn5 to correct that. The signal level being recorded for Analog In 5

will not change, but the level through the outputs as you are monitoring the performance will

go down.

The Fader position is specific to the connection between the input and an output. So, using

the example above, if you have attenuated the signal of Analog Input 5, through Analog

Outputs 3+4, but then you select Analog Output 1+2 from the Output Pane, the fader for the

Input will return to whatever position is established for that connection.

To reiterate, the faders are for the level of a specific connection between an input and an

output. It will not effect the level of the input source monitored through an output that is not

selected, nor will it effect the level of the audio being recorded.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Aurora LT-TB Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info