Bedienungsanleitung Lynx ONE (Seite 22 von 36) (Englisch)

586987

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Page 22

Troubleshooting

When Windows starts I see a LynxONE Mixer error - “No mixer device

drivers are available”.

This error will appear when the LynxONE Mixer is loading during Windows startup

and the LynxONE is not installed correctly. You should check the following items:

1. With the computer power off, verify that the card is properly seated in the PCI

slot.

2. Verify the LynxONE’s resources are not conflicting with some other device in

your system. For Windows 95/98, check in the Device Manager (Start > Control

Panel > System > Device Manager > Sound, video and game controllers >

LynxONE > Resources) to verify there are no resource conflicts. For Windows

NT check in Windows NT Diagnostics (Start > Programs Administrative Tools >

Windows NT Diagnostics > Resources) to verify there are no resource conflicts.

If there is a resource conflict, you may need to move the LynxONE to a different

slot in your computer as some motherboards have specific resources assigned to

specific slots, or change the interrupt setting in the BIOS setup screen. Please

refer to your motherboard/computer documentation to determine how to change

the interrupt for a PCI device.

I installed the LynxONE in the PCI slot before I ran Setup.exe for Windows

95/98, what do I do now?

The device manager in Windows 95/98 requires the .INF file for a device to be installed

before the Plug and Play scan to detect new hardware (which happens on each boot).

This is why Setup.exe should generally be run before you install the LynxONE into

your computer. To correct this follow the steps listed here:

1. Load the device manager by clicking on Start > Control Panel > System > Device

Manager.

2. There should be an entry called “+ ? Other Devices” listed about 3/4 down the

page. Click on the + sign. “PCI Multimedia Audio Device” should appear.

3. Click on "PCI Multimedia Audio Device", then click on "Remove".

4. A "Confirm Device Removal" dialog box should appear, click on “OK”. It might

take a couple of seconds for this dialog box to close.

5. Click on "Refresh". After several seconds, a "New Hardware Found" dialog box

will appear. Depending on your installation of Windows 95/98, another dialog

box may appear asking for setup disk. The location you need to specify is:

C:\Windows\System

Click on “OK” after entering this path.

6. You may need to reboot your machine once this completes to get everything running

properly.

The meters in the LynxONE Mixer do not show activity when I am

monitoring from the analog or digital inputs.

This is normal. The meters will show activity only when the card is in record or playback

mode while being used with a third party application. If metering is required for

monitoring, most applications offer this functionality by simply putting the card in

record mode without saving data to a disk file. However, for the lowest latency monitor

listening, use the LynxONE’s on-board monitor capabilities.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx ONE Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info