Bedienungsanleitung Lynx ONE (Seite 23 von 36) (Englisch)

586987

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Page 23

Troubleshooting

I cannot record from the LynxONE’s digital input.

The LynxONE Digital Input device must be configured as the record device in your

application. Select this device in the audio or wave device configuration menu. With

the device properly set, the meters in the LynxONE mixer will indicate the digital input

signal level while recording. See “Working with Third Party Applications” for more

information.

There is no signal on the digital output during playback.

The LynxONE Digital Output device must be configured as the playback device in

your application. Please refer to the previous question.

Audio playback sounds really slow or erratic.

The Sample Clock Source selected in the LynxONE Mixer is not connected to an

active clock source. In this case, the sample clock generator on the LynxONE runs

very slow or erratic. This will occur if Digital is selected as the Sample Clock Source

and there is either no connection to the LynxONE’s digital input or the device connected

is turned off. The same situation will occur if either External or Header is the selected

as the clock source and there is no connection to the corresponding inputs on the card.

Audio playback sounds fast or slow when I am using the digital input as

the clock source.

When the digital input is selected as the clock source, the LynxONE’s sample clock

will run at the sample rate of the incoming digital input signal. In the case when the

sample rate of this signal is 48 kHz and a file being played was actually recorded at

44.1 kHz, the audio will playback fast. To solve this problem either change the sample

rate of the device driving the digital input or select Internal as the sample clock source

using the LynxONE mixer.

I cannot change the Sample Clock Source from Digital in the LynxONE

Mixer.

Either the Monitor Source is set to Digital In or an application is actively recording

from the digital input. Under either condition, the LynxONE must synchronize to the

digital input in order to extract data. If the Monitor Source is set to Digital In change it

to Analog In. If an application is recording from the digital input discontinue that

operation first, then change the Clock Source selection.

How do I minimize record monitor latency when I am doing overdubs?

Use the LynxONE’s on-board monitor circuitry. This is controlled by the LynxONE

mixer.

What does the green LED on the LynxONE indicate?

When lit, the LED indicates successful initialization of the LynxONE and the driver.

How do I synchronize my LynxONE with a DPS Perception Video Recorder

card?

Using the Internal Clock Cable available from Lynx, you can connect the PVR’s 27

MHz clock to the LynxONE to maintain perfect A/V sync. Instructions for making this

connection and configuring the sample clock are included with the cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx ONE Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info