534675
28
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
28
TROUBLESHOOTING
Can’t load filament?
If you are having problems loading filament
into one of the extruders, perform the
following steps:
1. Go to the LCD panel and select Utilities
> Filament Options > Unload. This option
heats the extruders.
2. Set the extruder arm to the open position.
3. Make a fresh cut at the end of the
filament. It is important that the filament
have nobends in it. If it does, cut o the
bentsection of filament.
4. Insert the filament into the hole at the top
of the extruder. Keep pushing it in until you
start to see plastic come out of the nozzle.
5. When the filament is successfully
loaded, set the extruder lever arm to the
closed position.
If filament still doesn’t emerge from the
nozzle, remove the filament from the top of
the extruder and check for a bend at the end
of the filament. If the filament is bent, it is
possible that the filament is slipping under
the extruder bearing instead of entering the
extruder heater. Remove the extruder fan
and assembly using the instructions in the
section Disassembling an Extruder. This
will allow you to watch the filament travel
through the extruder and determine where
the filament is getting stuck.
It is also possible that you are unable to load
filament because a broken piece of filament
remains inside of the extruder. Remove
the extruder fan and assembly using the
instructions in the section Disassembling
an Extruder and use a pair of pliers to
remove the broken end of filament.
Extruder arms open
Extruder arms closed
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MakerBot Replicator 2X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info