534675
29
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
Can’t unload filament?
If you cannot unload filament from one of
the extruders, do the following:
1. Go to the LCD panel and select Utilities
> Filament Options > Unload. This option
heats the extruders.
2. Set the extruder lever arm to the
open position.
3. Push about half an inch of filament
through the extruder.
4. Try pulling the filament out of the
extruder again.
Extruder stays heated aer loading or
unloading filament?
If your extruder stays hot aer loading
filament or unloading filament, you
might have enabled the Preheat option.
To turn o the Preheat option, go to the
LCD panel and select Preheat > Cool. This
disables the heaters.
29STARTUP
TROUBLESHOOTING CONTINUED
To disassemble an extruder:
1. Unload the MakerBot Filament from the
extruder. To run the script for unloading
filament, go to the LCD panel and select
Utilities > Filament Options > Unload.
2. Switch o the power on the MakerBot
Replicator 2X and unplug the power
supply. Pull on the connector to release it
from the power input port.
3. Unscrew the two bolts at the lower corners
of the fan guard using your 2.5mm hex
wrench. As one piece, remove the fan guard,
the fan, the heat sink, and the spacers. Keep
these pieces assembled and move them
out of the way.
4. Unplug the motor wire harness from
the top of the extruder motor and slide
the motor assembly out of the extruder.
5. The extruder is now broken down into
its main assemblies.
Disassembling an Extruder
Occasionally you may need to take an extruder apart for troubleshooting purposes. This is a
simple process that will require no tools other than the 2.5 mm hex wrench you received with
your MakerBot Replicator 2X.
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MakerBot Replicator 2X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info