534675
95
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
Your MakerBot Replicator 2X Experimental
3D Printer uses ABS plastic filament, 1.75
mm in diameter, to print objects. [Fig 14.1]
The Replicator 2X can also use 1.75 mm
filament made from other plastics with
similar properties. The filament used in 3D
printing is also known as plastic welding
rod and is used in other applications, but
filament made for 3D printing needs to be
more consistent in diameter.
Sometimes 1.75 mm plastic filament can
vary in size between 1.65 mm and 1.85 mm.
[Fig 14.2] The extruders in the MakerBot
Replicator 2X can accommodate this
range of sizes. The consistency of filament
diameter is more important than the size
of the diameter. Filament that is thicker in
some places than in others is dicult for the
extruder to grip. It can also result in poor print
quality: a section of plastic that is too thin
will result in a section of your print that does
not contain enough plastic and a section
of filament that is too thick will result in a
section of your print that contains too much.
If you load a new roll of filament that is
slightly more thick or thin than your previous
roll, the extruders might feed too much or too
little plastic for your print. To fix this problem,
adjust the feedstock diameter in the
MakerBot Slicer through the custom profiles
feature in MakerWare. For more on custom
profiles and the feedstock diameter setting,
see the Advanced MakerWare settings page
at www.makerbot.com/support/makerware/
documentation/advanced.
Be careful with your filament. Keep it dry;
humidity might cause it to expand. Avoid
letting the filament loosen on the roll; this
can result in tangles which could cause your
filament to break or get stuck during a print
and the print to fail.
FILAMENT BASICS
95FILAMENT
1 mm
1.65
1.75
1.85
Fig. 14.1
1 milimeter = 1 inch Fig. 14.2
95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MakerBot Replicator 2X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info