Bedienungsanleitung Makita 2012 NB (Seite 8 von 17) (Englisch, Holländisch)

448175

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

1. Removing blades

Loosen the thumb screw which secures the chip

cover and remove the chip cover. Remove the

screws which secure the right side cover. Then

remove the right side cover. Turn the pulley until the

drum can be locked in the position whereby the

blade installation bolts face upward. (Fig. 8)

For throw away blades only

Place the two magnetic holders on the set plate and

push them in the direction of the arrow until the claw

contact the blade. Remove the six blade installation

bolts using the socket wrench. Grip the magnetic

holders and raise them straight up to remove the set

plate and the blade from the drum. Press the lock

plate and turn the pulley 180° to lock the drum.

Remove the other blade as described above. (Fig. 9

& 10)

For standard blades only

Remove the six installation bolts using the socket

wrench. Raise the set plate and blade straight up to

remove them from the drum. Press the lock plate

and rotate the drum by turning the pulley 180° to

lock the drum. Remove the other blade as described

above. Remove the set plate from the blade. (Fig. 11

& 12)

2. Installing blades

CAUTION:

• Use only Makita socket wrench provided to tighten

the blade installation bolts. The use of any other

socket wrench may cause overtightening or insuffi-

cient tightening of the bolts, resulting in severe

injury.

For throw away blades only

Provide a flat wood block approximately 300 mm

long and 100 mm wide. Place the blade and the set

plate on the wood block so that the blade locating

lug of the set plate rests in the groove of the blade.

Adjust the set plate so that both ends of the blade

protrude approximately 1 mm beyond the end of the

set plate. Place the two magnetic holders on the set

plate and push them until the claw contacts the

blade. (Fig. 13)

Grip the magnetic holder and slip the heel of the set

plate into the groove in the drum. Install the blade

installation bolts. (Fig. 9)

After tightening all the blade installation bolts lightly

and evenly from the center to the outside, tighten

them completely following the same sequence.

Remove the magnetic holders from the set plate.

Install the other blade as described above. Rotate

the drum slowly while pressing the lock plate to

make sure there is nothing abnormal. Then install

the chip cover and the side cover. (Fig. 10)

CAUTION:

• Do not tighten the blade installation bolts without

the blade locating lug of the set plate correctly

resting in the groove of the blade. This may cause

damage to the blade and potential injury to the

operator.

• Do not turn the tool on with the chip cover

removed.

• When installing the chip cover, make sure that the

chain is not caught by the chip cover.

For standard blades only

Place the blade on the blade gauge so that the blade

edge is perfectly flush with the inside of the front rib

(A). Place the set plate on the blade, then gently

press the heel of the set plate flush with the back

side of the blade gauge (B). Tighten the screws to

secure the set plate to the blade.

Slip the heel of the set plate into the groove in the

drum. Install the blade installation bolts. (Fig. 14)

After tightening all the blade installation bolts lightly

and evenly from the center to the outside, tighten

them completely following the same sequence.

(Fig. 15)

Install the other blade as described as above. Rotate

the drum slowly while pressing the lock plate to

make sure there is nothing abnormal. Then install

the chip cover and the side cover. (Fig. 16)

CAUTION:

• Tighten the blade installation bolts securely when

installing the blades.

• Do not turn the tool on with the chip cover open.

• When installing the chip cover, make sure that the

chain is not caught by the chip cover.

Changing type of blade

This tool can accept either throw away blades or standard blades. If you wish to change the type of blade, buy and use

the following parts.

Hood set (Fig. 17)

When you wish to maintain clean operations through easy dust collection, connect the vacuum cleaner to the thick-

nesser using this hood.

Loosen the thumb screws which secure the chip cover. Attach the hood to the thicknesser and secure the chip cover

and the hood together by tightening the thumb screws.

CAUTION:

• When installing the hood set, make sure that the chain is not caught by the chip cover or hood set. (Fig. 18)

Changing from standard blade to throw-away blade Changing from throw-away blade to standard blade

Set plate 2 pcs. Set plate 2 pcs.

Throw-away blade (306 mm) 2 pcs. Pan head screw M 4 x 6 4 pcs.

Magnetic holder 2 pcs. Standard blade 2 pcs.

Blade gauge 1 pc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 2012 NB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 2012 NB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info