Bedienungsanleitung Makita 2012 NB (Seite 9 von 17) (Englisch, Holländisch)

448175

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

OPERATION

CAUTION:

• Two or more pieces of narrow but similar thickness stock can be passed through the thicknesser side by side. How-

ever, allow some spacing between the stock to permit the feed rollers to grip the thinnest piece of stock. Otherwise, a

slightly thinner piece could be kicked back by the cutterhead.

Place the workpiece flat on the table top.

Determine the depth of cut as described before.

Switch on the tool and wait until the blades attain full speed. The workpiece should not be in contact with the feed roller

when you turn the tool on.

Then insert the workpiece flush with the table top.

When cutting a long or heavy workpiece, lift up its end slightly at the start and the end of the cut to avoid gouging or

snipping at the extreme ends of the workpiece.

The use of the tool top enables quick, effortless return of the workpiece to the infeed table side. This is especially con-

venient with two operators. (Fig. 19)

CAUTION:

• The workpiece with the following dimensions cannot be fed into the tool because the interval between two feed roll-

ers is 129 mm. Do not try to cut them. (Fig. 20)

• Stop the tool when the workpiece has stalled. Allowing the tool to run with a stalled workpiece causes rapid wearing

of the feed rollers.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

Adjusting height of sub-table (Fig. 21 & 22)

The height of sub-table is factory-adjusted. If further

adjustment is necessary, proceed as follows.

Place a postcard on the table and also place a ruler on

the postcard. Turn the adjusting screw with the hex

wrench until the end of the sub-table contacts the ruler.

Now the end of the sub-table is from 0.1 mm to 0.3 mm

above the table surface.

Replacing carbon brushes (Fig. 23 & 24)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Keeping blades sharp

Dull blades can cause rough finish, an overload of the

motor and dangerous kickback of the workpiece.

Replace dull blades immediately.

Lubrication (Fig. 25)

Oil the chain (after removing the side cover R), the four

columns and the screws for elevating the main frame.

This periodic lubrication should be performed with

machine oil.

CAUTION:

• Oiling and all maintenance should be done with the tool

turned off and unplugged.

Cleaning

Always brush off dirt, chips and foreign matter adhering

to the roller surfaces, motor vents and drums.

Limit for re-sharpening of standard blade (Fig. 26)

Do not use the standard blade whose blade length is

under 4 mm.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

1 Less than 130 mm long

2 Having a groove more than 130 mm wide

3 Having grooves at intervals of 130 mm wide

Less than 130 mm

More than 130 mm

130 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 2012 NB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita 2012 NB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info