Bedienungsanleitung Makita 2414NB (Seite 6 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598732

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

11. Before using the tool on an actual workpiece, let

it simply run for several minutes first. Watch for

flutter or excessive vibration that might be

caused by poor installation or a poorly balanced

wheel.

12. Watch out for flying sparks when operating.

They can cause injury or ignite combustible

materials.

13. Remove material or debris from the area that

might be ignited by sparks. Be sure that others

are not in the path of the sparks. Keep a proper,

charged fire extinguisher closely available.

14. Use the cutting edge of the wheel only. Never

use side surface.

15. If the wheel stops during the operation, makes

an odd noise or begins to vibrate, switch off the

tool immediately.

16. Always switch off and wait for the wheel to come

to a complete stop before removing, securing

workpiece, working vise, changing work posi-

tion, angle or the wheel itself.

17. Do not touch the workpiece immediately after

operation; it is extremely hot and could burn

your skin.

18. Store wheels in a dry location only.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Securing cut-off (Fig. 1)

This tool should be bolted with two bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 2)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

For tool with lock button

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop. For continuous operation, pull

the switch trigger and then push in the lock button. To

stop the tool from the locked position, pull the switch trig-

ger fully, then release it.

For tool with lock-off button

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

Spark guard (Fig. 3)

The spark guard is factory-installed with its lower edge

contacting the base. Operating the tool in this position

will cause many sparks to fly around. Loosen the screw

and adjust the spark guard to a position at which mini-

mum sparks will fly around.

Interval between vise and guide plate (Fig. 4 & 5)

The original spacing or interval between the vise and the

guide plate is 0 – 170 mm. If your work requires wider

spacing or interval, proceed as follows to change the

spacing or interval.

Remove the two hex bolts which secure the guide plate.

Move the guide plate as shown in the figure and secure it

using the hex bolts. The following interval settings are

possible:

35 – 205 mm

70 – 240 mm

CAUTION:

• Remember that narrow workpieces may not be secured

safely when using the two, wider interval settings.

Setting for desired cutting angle (Fig. 6)

To change the cutting angle, follow the procedure below:

1. Loosen the two hex bolts.

2. Set the guide plate to the desired angle (0° – 45°).

3. For more accurate angle, use a protractor or triangle

ruler. Keep the handle down so that the cut-off wheel

extends into the base. At the same time, adjust the

angle between the guide plate and the cut-off wheel

with a protractor or triangle ruler.

4. Tighten the hex bolts securely. At this time, make

sure that the guide rule does not move.

5. Check the angle again.

CAUTION:

• Never perform miter cuts when the guide plate is set at

the 35 – 205 mm or 70 – 240 mm position.

NOTE:

• The scale on the guide plate is only a rough indication.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing cut-off wheel (Fig. 7)

To remove the wheel, raise the safety guard. Press the

shaft lock so that the wheel cannot revolve and use the

socket wrench to loosen the hex bolt by turning it coun-

terclockwise.

Then remove the hex bolt, outer flange and wheel.

(Note: Do not remove the inner flange, ring and O-ring.)

To install the wheel, follow the removal procedures in

reverse. (Fig. 8)

CAUTION:

• Be sure to tighten the hex bolt securely. Insufficient

tightening of the hex bolt may result in severe injury.

Use the socket wrench provided to help assure proper

tightening.

• Always use only the proper inner and outer flanges

which are provided with this tool.

• Always lower the safety guard after replacing the

wheel.

Securing workpiece (Fig. 9)

By turning the vise handle counterclockwise and then

flipping the vise nut to the left, the vise is released from

the shaft threads and can be moved rapidly in and out.

To grip workpieces, push the vise handle until the vise

plate contacts the workpiece. Flip the vise nut to the right

and then turn the vise handle clockwise to securely retain

the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 2414NB Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info