Bedienungsanleitung Makita 2414NB (Seite 7 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598732

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

CAUTION:

• Always set the vise nut to the right fully when securing

the workpiece. Failure to do so may result in insufficient

securing of the workpiece. This could cause the work-

piece to be ejected or cause a dangerous breakage of

the wheel.

When the cut-off wheel has worn down considerably, use

a spacer block of sturdy, non-flammable material behind

the workpiece as shown in the figure. You can more effi-

ciently utilize the worn wheel by using the mid point on

the periphery of the wheel to cut the workpiece. (Fig. 10)

When cutting workpieces over 65 mm wide at an angle,

attach a straight piece of wood (spacer) over 190 mm

long x 45 mm wide to the guide plate as shown in the fig-

ure. Attach this spacer with screws through the holes in

the guide plate. (Fig. 11)

If you use a spacer block which is slightly narrower than

the workpiece as shown in the figure, you can also utilize

the wheel economically. (Fig. 12)

Long workpieces must be supported by blocks of non-

flammable material on either side so that it will be level

with the base top. (Fig. 13)

OPERATION

Hold the handle firmly. Switch on the tool and wait until

the wheel attains full speed before lowering gently into

the cut. When the wheel contacts the workpiece, gradu-

ally bear down on the handle to perform the cut. When

the cut is completed, switch off the tool and WAIT UNTIL

THE WHEEL HAS COME TO A COMPLETE STOP

before returning the handle to the fully elevated position.

CAUTION:

• Proper handle pressure during cutting and maximum

cutting efficiency can be determined by the amount of

sparks that is produced while cutting. Your pressure on

the handle should be adjusted to produce the maxi-

mum amount of sparks. Do not force the cut by apply-

ing excessive pressure on the handle. Reduced cutting

efficiency, premature wheel wear, as well as, possible

damage to the tool, cut-off wheel or workpiece may

result.

Cutting capacity

Max. cutting capacity varies depending upon the cutting angle and workpiece shape. Applicable wheel diameter:

355 mm

For tools with the under cover (Fig. 14)

To remove the collected dust from the under cover, place

the tool with its side up and pull the under cover open

after removing the wing bolt as shown in the figure. Be

sure to close and secure the under cover with the wing

bolt after the removal of dust.

Carrying tool (Fig. 15)

Fold down the tool head to the position where you can

attach the chain to the hook on the handle.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 16 & 17)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

Workpiece

shape

Cutting

angle

90° 115 mm 119 mm

115 mm x 130 mm

102 mm x 194 mm

70 mm x 233 mm

137 mm

45° 115 mm 106 mm 115 mm x 103 mm 100 mm

A x B B

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita 2414NB Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info