Bedienungsanleitung Makita AC320H (Seite 7 von 228) (Alle Sprachen)

598387

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

b. Do not place compressor under inflammable,

explosive or erosive service.

c. Do not overturn it or lift it with hooks and ropes.

DUTY CYCLE

All Makita manufactured air compressor are

recommended to be operated at no more than a 50% duty

cycle. This means an air compressor that pumps air more

than 50% of one hour is considered misuse because the

air compressor is undersized for the required air demand.

GENERAL INFORMATION

This air compressor is equipped with an Oil-Less pump

designed for durability and no maintenance.

The compressor can be used for properly rated pneumatic

nailers and staplers. An air pressure regulator is supplied

for these applications.

WARNING:

Never use compressor for applications other than to

operate a properly rated nailer and stapler. Use of the

compressor for other applications could result in property

damage and personal injury.

Separate air filter regulators combine the functions of air

regulation and/or moisture and dirt removal should be

used where applicable.

ON-RECEIPT INSPECTION

DAMAGE: Each air compressor outfit is carefully tested

and checked before shipment. With importer handling,

damage may result in transit and cause problems with

compressor operation.

Immediately upon arrival, check equipment for both

concealed and visible signs of damage to avoid expenses

being incurred to correct such problems. This should be

done regardless of any visible signs of damage to the

shipping container. If this product was shipped directly to

you, report any damages to the carrier and arrange for

inspection of goods immediately.

STORAGE

Before you store the air compressor, make sure you do

the following:

1. Review the “Maintenance” and “Operating

Procedures” sections and perform maintenance as

necessary. Be sure to drain water from air tank.

Protect the electrical cord and air hose from damage

(such as being stepped on or run over). Store the air

compressor in a clean and dry location.

DESCRIPTION OF OPERATION

DRAIN VALVE:

The drain valve is located between two sets of air tank

and is used to drain condensation with locating at a level

from the tank at the end of each use or daily.

OPERATION PANEL:

Operation Panel has power switch and mode select

switch. You can change the operation mode “CUT-IN

PRESSURE” and electrical current by mode select switch.

SWITCH:

Turn this switch to ON “|” to provide automatic power to

the pressure switch and to OFF “O” to remove power

when finished using the compressor or when compressor

will be left unattended.

This switch has a function of reset. When a thermal

protector operates, activating the function of reset, the

power is removed. Whenever the thermal protector

operates, a function of reset is activated. So even if you

turn the switch to ON “|”, compressor does not operate.

THERMAL PROTECTOR:

This compressor has a thermal protector. If the motor is

overheated by any cause, the motor is stopped by

operating a function of reset for a thermal protector.

After the motor has cooled down, the thermal protector

does not active.

PRESSURE CENSOR:

The pressure censor automatically starts the motor when

the air tank pressure drops to the factory set “cut-in”

pressure. It stops the motor when the air tank pressure

reaches the factory set “cut-out” pressure.

RELIEF VALVE:

If the pressure censor dose not shut off the air

compressor at its “cut-out” pressure setting, the relief

valve will protect against high pressure by “popping out” at

its factory set pressure which is slightly higher than the

pressure censor “cut-out” setting.

OUTLET PRESSURE GAUGE:

The outlet pressure gauge indicates the air pressure

available at the outlet side of the regulator. This pressure

is controlled by the regulator and is always less or equal

to the tank pressure. See “Operating Procedures”.

TANK PRESSURE GAUGE:

The tank pressure gauge indicates the air pressure in the

tank.

REGULATOR:

The air pressure coming from the air tank is controlled by

the regulator knob. Turn the knob clockwise to increase

pressure and counter-clockwise to decrease pressure. To

avoid minor re-adjustment after making a change in

pressure setting, always approach the desired pressure

from a lower pressure. When reducing from a higher to a

lower setting, first reduce the pressure less than the

desired pressure. Depending on the air requirements of

each particular accessory, the outlet regulated air

pressure may have to be adjusted while you are operating

the accessory.

COMPRESSED AIR OUTLET; “HP” marking

For High Pressure Pneumatic Tool Exclusive Use

Outlet Max Pressure; 2.45 MPa (24.5 bar)

COMPRESSED AIR OUTLET; “RP” marking

For Regular Pressure Pneumatic Tool Use

Outlet Max Pressure; 0.88 MPa (8.8 bar)

INSTALLATION AND BREAK-IN

PROCEDURES

LOCATION OF THE AIR COMPRESSOR

Locate the air compressor in a clean, dry and well-

ventilated area. The air filter must be kept clear of

obstructions, which could reduce air delivery of the air

compressor. The air compressor should be located at

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AC320H Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita AC320H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info