Bedienungsanleitung Makita BKP140 (Seite 9 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598577

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

(A) Front base (Movable shoe)

(B) Rear base (Stationary shoe)

Dust bag (accessory) (Fig. 12)

For tool without nozzle

Remove the chip cover and install the nozzle (optional

accessory). Attach the dust bag onto the nozzle. The

nozzle is tapered. When attaching the dust bag, push it

onto the nozzle firmly as far as it will go to prevent it from

coming off during operation.

For tool with nozzle

Attach the dust bag onto the nozzle. The nozzle is

tapered. When attaching the dust bag, push it onto the

nozzle firmly as far as it will go to prevent it from coming

off during operation. (Fig. 13)

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust bag

of its contents, tapping it lightly so as to remove particles

adhering to the insides which might hamper further

collection.

NOTE:

• If you connect a Makita vacuum cleaner to this tool,

more efficient and cleaner operations can be

performed.

Connecting a vacuum cleaner (Fig. 14)

For tool without nozzle

When you wish to perform clean planing operation,

connect a Makita vacuum cleaner to your tool. Before

connecting the vacuum cleaner, remove the chip cover

from the tool. Then connect a hose of the vacuum cleaner

to the nozzle (optional accessory) as shown in the figures.

For tool with nozzle

When you wish to perform clean planing operation,

connect a Makita vacuum cleaner to your tool. Then

connect a hose of the vacuum cleaner to the nozzle as

shown in the figures.

Elbow (optional accessory) (Fig. 15)

Use of elbow allows change of chip discharge direction to

perform cleaner work.

For tool without nozzle

Remove the chip cover and install the nozzle (optional

accessory). Attach the elbow (optional accessory) on the

nozzle of the tool by just slipping on it. To remove it, just

pull it out.

For tool with nozzle

Attach the elbow (optional accessory) on the nozzle of the

tool by just slipping on it. To remove it, just pull it out.

OPERATION

Hold the tool firmly with one hand on the knob and the

other hand on the switch handle when performing the tool.

Planing operation (Fig. 16)

First, rest the tool front base flat upon the workpiece

surface without the blades making any contact. Switch on

and wait until the blades attain full speed. Then move the

tool gently forward. Apply pressure on the front of tool at

the start of planing, and at the back at the end of planing.

Planing will be easier if you incline the workpiece in

stationary fashion, so that you can plane somewhat

downhill.

The speed and depth of cut determine the kind of finish.

The power planer keeps cutting at a speed that will not

result in jamming by chips. For rough cutting, the depth of

cut can be increased, while for a good finish you should

reduce the depth of cut and advance the tool more slowly.

Shiplapping (Rabbeting) (Fig. 17)

To make a stepped cut as shown in the figure, use the

edge fence (guide rule) which is obtained as accessory.

(Fig. 18)

Draw a cutting line on the workpiece. Insert the edge

fence into the hole in the front of the tool. Align the blade

edge with the cutting line. (Fig. 19)

Correct setting Although this side view cannot show it, the

edges of the blades run perfectly parallel to

the rear base surface.

Nicks in surface Cause: One or both blades fails to have edge

parallel to rear base line.

Gouging at start Cause: One or both blade edges fails to

protrude enough in relation to rear

base line.

Gouging at end Cause: One or both blade edges protrudes

too far in relation to rear base line.

(A)

(B)

(A)

(B)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BKP140 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info