Bedienungsanleitung Makita BKP140 (Seite 10 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598577

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Adjust the edge fence until it comes in contact with the

side of the workpiece, then secure it by tightening the

screw. (Fig. 20)

When planing, move the tool with the edge fence flush

with the side of the workpiece. Otherwise uneven planing

may result.

Maximum shiplapping (rabbeting) depth is 9 mm. (Fig. 21)

You may wish to add to the length of the fence by

attaching an extra piece of wood. Convenient holes are

provided in the fence for this purpose, and also for

attaching an extension guide (optional accessory).

Chamfering (Fig. 22 & 23)

To make a chamfering cut as shown in the figure, align

the “V” groove in the front base with the edge of the

workpiece and plane it.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Sharpening the planer blades

For conventional blades only (Fig. 24)

Always keep your blades sharp for the best performance

possible. Use the sharpening holder (optional accessory)

to remove nicks and produce a fine edge. (Fig. 25)

First, loosen the two wing nuts on the holder and insert

the blades (A) and (B), so that they contact the sides (C)

and (D). Then tighten the wing nuts. (Fig. 26)

Immerse the dressing stone in water for 2 or 3 minutes

before sharpening. Hold the holder so that the both blades

contact the dressing stone for simultaneous sharpening at

the same angle.

Replacing carbon brushes (Fig. 27)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 28 & 29)

Use a screwdriver to remove the chip cover or nozzle.

(Fig. 30)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• High-speed steel Planer blade

• Tungsten-carbide Planer blade (For longer blade life)

• Mini planer blade

• Sharpening holder assembly

• Blade gauge

• Set plate set

• Edge fence (Guide rule)

• Extension guide set

• Dressing stone

• Nozzle

• Dust bag assembly

• Elbow

• Socket wrench

• Plastic carrying case

• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model BKP140

Sound pressure level (L

): 80 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model BKP180

Sound pressure level (L

): 84 dB (A)

Sound power level (L

): 95 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model BKP140

Work mode: planing softwood

Vibration emission (a

): 3.5 m/s

Uncertainty (K): 1.5 m/s

Model BKP180

Work mode: planing softwood

Vibration emission (a

): 4.5 m/s

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BKP140 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info