Bedienungsanleitung Makita bmr 100 (Seite 8 von 19) (Englisch, Holländisch)

407552

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

3. BH2433 | BH2420After back up batteries are inserted,

insert the main battery pack to power radio. The

suitable battery packs for this radio listed as below.

Cluster Battery:

9.6V: 9135 | 9134 | 9122 | PA09 | 9120

12V: 1235 | 1234 | 1222 | PA12 | 1220

14.4V: 1435 | 1434 | 1422 | PA14 | 1420

18V: 1835 | 1834 | 1822 | PA18

Slide Battery:

9.6V: BH9033 | BH9033A | BH9020 | BH9020A

12V: BH1233 | BH1233C | BH1220C

14.4V: BH1433 | BH1420 | BL1430

18V: BL1830

24V: BH2433 | BH2420

The following tables indicate the operating time on a

single charge.

* Operating time may differ by the type of battery, charging or

operating conditions.

3-1. Installing or removing Slide

battery cartridge (Fig. 3)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge

or pressing the buttons on both sides of the cartridge.

3-2. Installing or removing Cluster

battery cartridge (Fig. 4)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

• To remove the battery cartridge, withdraw it from the

Job site radio.

4. Replace battery compartment locker.

5. Reduced power, distortion and a “stuttering sound” or

low battery sign that appears on the display are

all the signs that the main battery pack needs to

replace.

Note:

The battery pack can't be charged via the supplied AC

power adaptor.

6. When low battery sign appears and an “E” keeps

on flashing is the time to replace the back up batteries.

Installing the Soft bended rod

antenna (Fig. 5)

Install the Soft bended rod antenna as show in the figure.

Using Supplied AC power adaptor

(Fig. 6)

Remove the rubber protector and insert the adaptor plug

into the DC socket on the front side of the radio. Plug the

adaptor into a standard mains socket outlet. Whenever

the adaptor is used, the battery pack are automatically

disconnected. The AC adaptor should be disconnected

from the main supply when not in use.

Setting the clock

1. Clock can be set either when the radio is power on or

off.

2. Display will show “-: - -” when the back up batteries

are installed.

3. Long press the time set button for more than

2 seconds, display will flash time set symbol and

also the hour digit, followed by a beep.

4. Rotate Tuning control to set the required hour.

5. Press button to confirm hour setting, the minute

digit will flash.

6. Rotate Tuning control to set the required minute.

7. Press the button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods – Scan

tuning, Manual tuning and Memory presets recall.

Scan Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Make sure the rubber bended rod antenna has

been well placed for best FM reception. For AM (MW)

band, rotate the radio to get best signal. Try to avoid to

operate the radio next to computer screen and other

equipment which will cause interference to the radio.

3. Press and release Scan button (long press Scan

button more than 2 seconds will activate time setting),

LCD display will flash Scan symbol and the radio will

up search and stop automatically when it finds a radio

station,. Press the Scan button again to pick up the

found station.

Battery

Capacity

Battery Cartridge•Voltage

Operating time*

(At Max. Volume)

9.6V 12V 14.4V 18V 24V

1.3 Ah

PA09

9120

PA12

1220

PA14

1420

PA18 – Approx. 7 hour

2.0 Ah

9122

BH9020

BH9020A

1222

BH1220C

1422

BH1420

1822 BH2420 Approx. 11 hour

2.6 Ah 9134 1234 1434 1834 – Approx. 13 hour

3.0 Ah 9135 1235

1435

BL1430

1835

BL1830

– Approx. 16 hour

3.3 Ah

BH9033

BH9033A

BH1233

BH1233C

BH1433 – BH2433 Approx. 17 hour

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita bmr 100 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita bmr 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info