Bedienungsanleitung Makita bsr 730 (Seite 8 von 19) (Englisch, Holländisch)

382504

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

14. Use the appropriate riving knife for the blade

being used. For the riving knife to work, it must be

thicker than the body of the blade but thinner than

the tooth set of the blade.

15. Adjust the riving knife as described in this

instruction manual. Incorrect spacing, positioning

and alignment can make the riving knife ineffective

in preventing kickback.

16. Always use the riving knife except when plunge

cutting. Riving knife must be replaced after plunge

cutting. Riving knife causes interference during

plunge cutting and can create kickback.

17. For the riving knife to work, it must be engaged

in the workpiece. The riving knife is ineffective in

preventing kickback during short cuts.

18. Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing rate of

a guard.

19. Use extra caution when cutting damp wood,

pressure treated lumber, or wood containing

knots. Adjust speed of cut to maintain smooth

advancement of tool without decrease in blade

speed.

20. Avoid Cutting Nails. Inspect for and remove all

nails from lumber before cutting.

21. Place the wider portion of the saw base on that

part of the workpiece which is solidly supported,

not on the section that will fall off when the cut is

made. As examples, Fig. 5 illustrates the RIGHT

way to cut off the end of a board, and Fig. 6 the

WRONG way. If the workpiece is short or small,

clamp it down. DO NOT TRY TO HOLD SHORT

PIECES BY HAND! (Fig. 5 & 6)

22. Never attempt to saw with the circular saw held

upside down in a vise. This is extremely danger-

ous and can lead to serious accidents. (Fig. 7)

23. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

24. Do not stop the blades by lateral pressure on the

saw blade.

25. Always use blades recommended in this manual.

Do not use any abrasive wheels.

26. Wear a dust mask and hearing protection when

use the tool.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 8)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the side of the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Removing or installing saw blade

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before removing or installing

the blade.

The following blade can be used with this tool.

The thickness of the riving knife is 1.8 mm.

CAUTION:

• Do not use saw blades which do not comply with the

characteristics specified in these instructions.

• Do not use saw blades the disc of which is thicker or

the set of which is smaller than the thickness of the riv-

ing knife.

To remove the blade, press the shaft lock so that the

blade cannot revolve and use the hex wrench to loosen

the bolt counterclockwise. Then remove the bolt, outer

flange and blade. (Fig.9)

To install the blade, follow the removal procedure in

reverse. BE SURE TO TIGHTEN THE BOLT SECURELY.

(Fig. 10)

CAUTION:

• Be sure the blade is installed with teeth pointing up at

the front of the tool.

• Use only the Makita hex wrench to remove or install the

blade.

Riving knife adjustment (Fig.11)

Use the hex wrench to loosen the hex socket head bolt

for the riving knife adjustment, then raise the safety cover

(safety guard). Move the riving knife up or down over the

protuberance for settings indicated in Fig.11, so as to

obtain the proper clearance between the riving knife and

saw blade.

CAUTION:

Ensure that the riving knife is adjusted such that:

The distance between the riving knife and the toothed rim

of the saw blade is not more than 5 mm. The toothed rim

does not extend more than 5 mm beyond the lower edge

of the riving knife.

Max. dia. Min. dia.

Blade

thickness

Kerf

190 mm 170 mm

1.6 mm

or less

1.9mm

or more

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita bsr 730 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita bsr 730

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info