Bedienungsanleitung Makita bsr 730 (Seite 9 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

382504

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Conditioning charge

Conditioning charge can extend the life of battery by automatically searching the optimum charging condition

for the batteries in every situation.

The battery employed in the following conditions repeatedly, will be worn out shortly, and yellow warning light

may flash.

1. Recharge of battery with its high temperature

2. Recharge of battery with its low temperature

3. Recharge of full charged battery

4. Over-discharge of battery (contunue to discharge battery in spite of down of power.)

5. Recharge under broken cooling system

The charging time of such battery is longer than usual.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the

charger will switch into its ‘‘trickle charge (maintenance charge)’’ mode and keep the battery cartridge fresh and

fully charged.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before charging it.

4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

NOTE:

•

The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other

manufacturer’s batteries.

•

When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of

time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can

recharge the battery cartridge fully after discharging it completely and recharging a couple of times.

•

If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location

exposed to direct sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a

while. When the temperature on battery is more than approx. 70°C, two charging lights may flash in red color,

and when approx. 50°C – 70°C, one charging light in red color. Charging will begin after the battery cartridge

is cooled by the cooling fan installed in the charger.

•

If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the

charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

•

Any of the following conditions indicates damage to the charger and/or battery cartridge. Ask your Makita

Authorized or Factory Service Center to check them.

1) The charging light does not flash (green) when the battery charger is plugged into a power source.

2) The charging light does not light up or flash (red) when the battery is inserted in the charger port.

3) Charging is not completed at even more than two hours after red light comes ON at start of charging.

Removing or installing saw blade

Important:

Always be sure that the tool is switched off and the

battery cartridge is removed before removing or

installing the blade.

The following blade can be used with this tool.

Max. dia. Min. dia.

Blade

thickness

Kerf

190 mm 170 mm

1.6 mm

or less

1.9 mm

or more

The thickness of the riving knife is 1.8 mm.

CAUTION:

•

Do not use saw blades which do not comply with the

characteristics specified in these instructions.

•

Do not use saw blades the disc of which is thicker or

the set of which is smaller than the thickness of the

riving knife.

To remove the blade, press the shaft lock so that the

blade cannot revolve and use the hex wrench to

loosen the bolt counterclockwise. Then remove the

bolt, outer flange and blade. (Fig. 10)

To install the blade, follow the removal procedure in

reverse. BE SURE TO TIGHTEN THE BOLT

SECURELY. (Fig. 11)

CAUTION:

•

Be sure the blade is installed with teeth pointing up

at the front of the tool.

•

Use only the Makita hex wrench to remove or install

the blade.

BSR730 (E) (’100. 3. 22)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita bsr 730 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita bsr 730

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info