Bedienungsanleitung Makita BTD145 (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598618

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Changing the hammering force (Fig. 6)

The hammering force can be changed in three steps:

hard, medium and soft.

This allows a tightening suitable to the work.

Every time the hammering force button is pressed,

the number of blows changes in three steps.

For approximately one minute after releasing the switch

trigger, the hammering force can be changed.

NOTE:

• When all lamps on the switch panel go out, the tool is

turned off to save the battery power. The hammer force

grade can be checked by pulling the switch trigger to

the extent that the tool does not operate.

• During the operation of switch trigger, the hammer

force grade cannot be changed.

Empty signal for remaining battery capacity (Fig. 7)

Pulling the trigger switch when the remaining battery

capacity becomes very low makes LED indicator flicker.

If the tool is used continuously with the LED indicator

flickering up and the battery power is almost used up, the

LED indicator will light up and the tool itself will stop.

Please refer to the following table for the LED indicator

status and the remaining battery capacity.

NOTE:

• When all lamps on the switch panel go out, the tool is

turned off to save the battery power. The remaining

battery capacity can be checked by pulling the switch

trigger to the extent that the tool does not operate.

• All of the lamps on the switch panel go out approxi-

mately one minute after releasing the switch trigger.

• When the tool temperature is high, the LED indicator

may flicker or light up.

• If the LED indicator lights up and the tool stops even

with a recharged battery cartridge, cool down the tool

temperature fully. When the status is still unchanged,

stop using and have the tool repaired by a Makita local

service center.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or socket bit

Use only bits that has inserting portion shown in the fig-

ure. (Fig. 8)

For tool with shallow bit hole (Fig. 9)

For tool with deep bit hole (Fig. 10)

Procedure 1

For tool without one-touch type

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

For tool one-touch type

To install the bit, insert the bit into the sleeve as far as it

will go.

Procedure 2

In addition to the procedure (1) above, insert the bit-piece

into the sleeve with its pointed end facing in.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

• When it is difficult to insert the bit, pull the sleeve and

insert it into the sleeve as far as it will go.

Hammering force grade

displayed on panel

Maximum blows

Application Work

BTD133 BTD145

Hard

3,200

(min

–1

)

3,400

(min

–1

)

Tightening when force and

speed are desired.

Tightening in underwork material /

Tightening long screws / Tightening

bolts.

Medium

2,600

(min

–1

)

2,800

(min

–1

)

Tightening when a good

finishing is needed.

Tightening in the finishing board,

plaster board.

Soft

1,100

(min

–1

)

1,300

(min

–1

)

Tightening when excessive

tightening need to be avoided

because of potentially clogged

female screw and broken or

damaged screw head.

Tightening sash screw / Tightening

small screws such as M6.

LED indicator status Remaining battery capacity

OFF

Enough

Flickering

20%

Lighting on Very low and the tool will

stop.

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for

installing the bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita BTD145 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info